Inductance Calculations of Permanent-Magnet Synchronous Machines Including Flux Change and Self- and Cross-Saturations

Meessen, K. J.; Thelin, Peter; Soulard, Juliette; Lomonova, E. A.

doi:10.1109/tmag.2008.2001419

Cited by 108 publications

(31 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The error between the analytically calculated, experimental, and FEM-modeled inductance values is about 17%. The analytical model does not take into account the excessive saturation of the teeth heads and the cross-saturation effects, which can be accurately taken into account only by the FEM [28], [29]. If semimagnetic slot wedges are used, the saturation at the stator teeth heads is decreased, which can be also accurately estimated only by the FEM.…”

Section: Resultsmentioning

confidence: 99%

Inductance Calculation of Tooth-Coil Permanent-Magnet Synchronous Machines

Ponomarev

Alexandrova

Petrov

et al. 2014

IEEE Trans. Ind. Electron.

View full text Add to dashboard Cite

Abstract-Analytical calculation methods for all the major components of the synchronous inductance of tooth-coil permanentmagnet synchronous machines are reevaluated in this paper. The inductance estimation is different in the tooth-coil machine compared with the one in the traditional rotating field winding machine. The accuracy of the analytical torque calculation highly depends on the estimated synchronous inductance. Despite powerful finite element method (FEM) tools, an accurate and fast analytical method is required at an early design stage to find an initial machine design structure with the desired performance. The results of the analytical inductance calculation are verified and assessed in terms of accuracy with the FEM simulation results and with the prototype measurement results.Index Terms-Fractional slot winding, inductance calculation, leakage inductance, permanent-magnet synchronous machine (PMSM), tooth coil.

show abstract

Section: Resultsmentioning

confidence: 99%

Inductance Calculation of Tooth-Coil Permanent-Magnet Synchronous Machines

Ponomarev

Alexandrova

Petrov

et al. 2014

IEEE Trans. Ind. Electron.

View full text Add to dashboard Cite

show abstract

“…However, inductances have to be calculated by considering saturation [5,6]. Under the saturation condition, inductances of WRSM can be calculated using FE analysis as follows.…”

Section: Basic Theory Of Controlmentioning

confidence: 99%

Current Control Method of WRSM in High-speed Operation Range

Lee

Jang

et al. 2015

Journal of Electrical Engineering and Technology

View full text Add to dashboard Cite

-This Paper analyzes the characteristics of the WRSM in high-speed operation range. To verify the control characteristics of various WRSM models, the relative position of the central point of current limit circle and voltage limit ellipse is defined as M value and 3 models according to M max value are designed through inductance change. Through the designed models, the current control method of 3-variables control for maximum power especially in high-speed operation range is presented.

show abstract

“…The machine electrical parameters must be identified in order to calculate the aforementioned LUTs. FEM analysis [26], [27] or experimental procedures [27], [28] are usually employed, from where electric machine d-and q-axis fluxes are obtained. Permanent magnet flux and d-and q-axis inductances can be calculated from these fluxes.…”

Section: Introductionmentioning

confidence: 99%

“…Permanent magnet flux and d-and q-axis inductances can be calculated from these fluxes. However, it is important to point out that an adequate mathematical approach must be followed [27].…”

Section: Introductionmentioning

confidence: 99%

“…However, LUT approaches tune the control algorithm for an specific set of electrical parameters and may eventually loss control under parameter variations due to an incorrect FW regulation, i.e., exceeding the stator voltage limit and leading to an uncontrolled energy regeneration [32]. The high non-linearities caused by the magnetic saturation effect [27] together with electrical parameter variations due to machine ageing, manufacture tolerances and temperature dependency confirm the importance of relying on a robust control strategy that ensures the correct operation of the EV drive during its whole lifecycle.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation