Hybrid active power filter based on the IRP theory for harmonic current mitigation

Cleary-Balderas, Arthur; Senior, A.; Cruz-Hernendez, O.

doi:10.1109/ropec.2016.7830608

Cited by 13 publications

(10 citation statements)

References 13 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The effective operation of current control algorithm is depending on instantaneous power theory that used in this simulation. The instantaneous power theory or p-q theory was introduced by Akagi in 1983 and this method uses algebra transformation, which is also known as Clarke transform, to be used in three-phase voltage and current [4,9,10,12,16]. This theory is the most popular harmonic extraction algorithm, which is usually used for three-phase three-wire SAPF.…”

Section: Methodsmentioning

confidence: 99%

“…Hence, Active Power Filter (APF) has been introduced to mitigate low and high harmonics distortion in the power system. In conjunction to that, APF can also be used for reactive power compensation, load balancing, voltage regulation and voltage flicker compensation [1,3,5,6,10,24]. Multilevel Inverter (MLI) has gained much intention in high power system application due to its advantages such as produce common mode voltage, draw low distortion input current, operate in low and high switching frequency, and can reduce harmonic distortion using selective harmonic elimination technique.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Performance of three-phase three-wire cascaded H-bridge multilevel inverter-based shunt active power filter

Lada

Radzi

Jasni

et al. 2020

IJPEDS

View full text Add to dashboard Cite

<span lang="EN-US">Multilevel inverter (MLI) becomes more significant in Active Power Filter (APF) application due to capability to its produce low harmonic output current in which at the same time improving performance of APF. Among the topologies of MLI, Cascaded H-Bridge (CHB) is the most popular topology with less power devices requirement and simple design. MLI CHB is also capable to produce possible output voltage at twice of the number of DC source which in this case of APF is the best suited topology to replace with the conventional six -step inverter. This paper presents the performance of three- phase three-wire CHB MLI used in Shunt Active Power Filter (SAPF) based on Direct Current Control (DCC) and Indirect Current Control (ICC) schemes. Both schemes are developed and verified in MATLAB/Simulink. The simulation results show that both current control algorithms are capable to mitigate load current with Total Harmonic Distortion below than the permissible value based on IEEE 519 standard.</span>

show abstract

Section: Methodsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Performance of three-phase three-wire cascaded H-bridge multilevel inverter-based shunt active power filter

Lada

Radzi

Jasni

et al. 2020

IJPEDS

View full text Add to dashboard Cite

show abstract

“…The unified power quality conditioner, UPQC, is utilized to solve all of the previous problems; this is called a universal active power filter and consists of a combination of shunt and series active power filters [38,39]. The hybrid active power filter is a combination of passive and active power filters and is used for high power applications [40][41][42][43][44][45][46]. As mentioned above, only the UPQC can mitigate all power quality problems.…”

Section: Introductionmentioning

confidence: 99%

Effect of Unified Power Quality Conditioner on Voltage and Current Waveforms

Mahmoud¹,

Mamdouh²,

Khalil

2021

Walailak J Sci & Tech

View full text Add to dashboard Cite

Power quality improvement faces different and significant problems due to voltage instability and the wide use of electronic power devices. To overcome these different power quality problems, an active power filter is used. The active power filter, in general, has 4 main categories- shunt, series, unified power quality conditioner, and hybrid active power filter. The shunt active power filter is usually used to mitigate source current harmonics and compensate reactive power for power factor correction. The series active power filter is usually used to mitigate voltage problems (sags, swells, transients, dips, distortions, harmonics, etc.). The unified power quality conditioner is a combination of the shunt active power filter and the series active power filter; it is used to mitigate all voltage and current problems, compensate voltage, current system harmonics, and reactive power compensation, and mitigate voltage dips, voltage sags, voltage swells, and voltage phase shift. In this paper, the 3-phase 3-wire unified power quality conditioner is utilized to mitigate all power system problems (voltages and currents) and discuss the effect of the shunt and series active power filter separately on source voltage and source current waveforms. This case study shows that the source voltage distortion can be mitigated by using the series active power filter alone, but the source current distortion cannot be mitigated without using both the series and shunt active power filter. The source current harmonic problem mainly exists due to 1) distorted voltage sources, and 2) non-linear loads. Therefore, the unified power quality conditioner must be used to mitigate source current distortions in the case of the distorted voltage source, to comply with the standard limits IEEE 519, IEC 555, and IEC 61000. HIGHLIGHTS The UPQC is used to mitigate all voltage and current problems and improve all power system quality The SEAPF eliminates all voltage problems The SHAPF has no effect on source voltage The SHAPF eliminates source current harmonic distortion GRAPHICAL ABSTRACT

show abstract

“…The second research direction is the search for new control algorithms. Apart from trying to apply one of the power theories [22][23][24][25], the authors use techniques such as: artificial neural networks [18,19], fuzzy logic [26][27][28][29], adaptive filters [28,30] or other methods [31][32][33][34]. The key issues here are also the methods of controlling the converter dc voltage [35][36][37] or the elimination of the influence of the supply voltage distortion on the operation of the HAPF [38,39].…”

Section: Introductionmentioning

confidence: 99%

Control Strategy of 1 kV Hybrid Active Power Filter for Mining Applications

et al. 2021

View full text Add to dashboard Cite

The paper presents a shunt hybrid active power filter for 1 kV mining applications in configuration with a single-tuned passive filter. The focus is on the method of controlling the filter, with particular emphasis on the influence of network voltage distortion and time delays in control on the effectiveness of harmonic reduction, which is one of the most important aspect of power quality. The low-power loss configuration of a hybrid filter with SiC transistors is shown, as well as the control algorithm which limits the influence of voltage distortion. Theoretical considerations are verified by results obtained from simulations and tests of the hybrid active power filter prototype.

show abstract

Hybrid active power filter based on the IRP theory for harmonic current mitigation

Cited by 13 publications

References 13 publications

Performance of three-phase three-wire cascaded H-bridge multilevel inverter-based shunt active power filter

Performance of three-phase three-wire cascaded H-bridge multilevel inverter-based shunt active power filter

Effect of Unified Power Quality Conditioner on Voltage and Current Waveforms

Control Strategy of 1 kV Hybrid Active Power Filter for Mining Applications

Contact Info

Product

Resources

About