High temperature oxidation resistance of electrodeposited Reduced Graphene Oxide (RGO) reinforced copper coating

Maharana, H.S.; Jena, Subrat Kumar; Basu, A.; Mondal, Kunal

doi:10.1016/j.surfcoat.2018.04.025

Cited by 17 publications

(8 citation statements)

References 47 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As well as improving the corrosion resistance, it has been demonstrated by Maharana et al [158] that an electrodeposited RGO reinforced copper coating on a copper substrate can also improve the oxidation resistance compared with a pure copper coating. The isothermal oxidation behaviour of the specimens with the different coatings at 406 and 542°C in air is shown in Fig.…”

Section: Oxidationmentioning

confidence: 99%

“…It can be seen that the mass gain of all the RGO-coated specimens is significantly less than that of the pure copper coatings. The oxidation protection mechanism is thought to be due to the RGO acting as an inherent barrier to diffusing gases [158].…”

Section: Oxidationmentioning

confidence: 99%

“…Based on the electrochemical corrosion studies performed on Cu and Cu/graphene coatings, it can be concluded that Cu/graphene composite coatings could be promising anti-corrosive coatings for long-term corrosion protection of steel in chloride environments such as sea water [112,113]. Reproduced with permission from [158].…”

Section: Potential Applicationsmentioning

confidence: 99%

See 2 more Smart Citations

Copper/graphene composites: a review

Hidalgo-Manrique

Lei²,

Xu³

et al. 2019

J Mater Sci

246

View full text Add to dashboard Cite

Recent research upon the incorporation of graphene into copper matrix composites is reviewed in detail. An extensive account is given of the large number of processing methods that can be employed to prepare copper/graphene composites along with a description of the microstructures that may be produced. Processing routes that have been employed are described including powder methods, electrochemical processing, chemical vapour deposition, layer-by-layer processing, liquid metal infiltration among a number of others. The mechanical properties of the composites are described in detail along with an account of the structural factors that control mechanical behaviour. The mechanics and mechanisms of deformation are discussed, and the effect of factors such as the graphene content and the type of graphene used, along with processing conditions for the fabrication of the composites, is described. The functional properties of copper/graphene composites are also reviewed including their electrical and thermal properties, and tribological and corrosion behaviour. In each case, the effect of the graphene type and content, and processing conditions are also described. Finally, possible future applications of copper/graphene composites are discussed.

show abstract

Section: Oxidationmentioning

confidence: 99%

Section: Oxidationmentioning

confidence: 99%

See 1 more Smart Citation

Copper/graphene composites: a review

Hidalgo-Manrique

Lei²,

Xu³

et al. 2019

J Mater Sci

246

View full text Add to dashboard Cite

show abstract

“…After oxidation, the formation of CuO along with existing FCC solid solutions and σ phase was observed in all the HEA samples. In spite of the presence of different elements, only Cu was oxidized due to its lower oxidation resistance in the present temperature range of discussion [22][23][24][25]. During high-temperature oxidation, ionic diffusion plays a major role by transferring metallic cation and oxygen anion.…”

Section: Xrd Analysismentioning

confidence: 85%

“…In another oxidation study of electrodeposited reduced graphene oxide (RGO) reinforced copper coating, it was reported that above the 400°C the Cu rich matrix follows the cubic rate law [22]:…”

Section: Oxidation Kinetics Of Heasmentioning

confidence: 99%

Oxidation study of CoCrCuFeNiSix high entropy alloys

Shajahan

Kumar

Chopkar

et al. 2020

Mater. Res. Express

View full text Add to dashboard Cite

Oxidation studies of Co-Cr-Cu-Fe-Ni-Si X=(0,0.3,0.6,0.9) high entropy alloys (HEA) at 600, 700 and 800°C for 30 h are performed in the present work. Isothermal oxidation confirmed that the oxidation resistance of Co-Cr-Cu-Fe-Ni-Si X=(0,0.3,0.6,0.9 ) high entropy alloy increases with Silicon (Si) content up to 0.6%, beyond that it decreases. Oxidation rate kinetics study of all the alloys at the three designated test temperature represented the typical cubic curve. X-ray diffraction (XRD) analysis revealed the evolution of Cu oxide (CuO) along with existing phases in all the HEA samples. Microstructural observation after oxidation test exhibited an increase in oxide formation with the oxidation temperature. To comprehend the kinetics of oxidation more clearly, Arrhenius plots were drawn for all the HEA samples and activation energies are calculated.

show abstract

The effect of candle-soot reinforced electroless Ni-P particle interface on tribological performance in copper-based materials produced by flake powder metallurgy method: Transfer of candle-soot from waste to solid-lubricant

Güler

2023

Colloids and Surfaces A: Physicochemical and Engineering Aspect

View full text Add to dashboard Cite

High temperature oxidation resistance of electrodeposited Reduced Graphene Oxide (RGO) reinforced copper coating

Cited by 17 publications

References 47 publications

Copper/graphene composites: a review

Copper/graphene composites: a review

Oxidation study of CoCrCuFeNiSix high entropy alloys

The effect of candle-soot reinforced electroless Ni-P particle interface on tribological performance in copper-based materials produced by flake powder metallurgy method: Transfer of candle-soot from waste to solid-lubricant

Contact Info

Product

Resources

About