Epitaxial growth of detachable GaAs/Ge heterostructure on mesoporous Ge substrate for layer separation and substrate reuse

Paupy, Nicolas; Ilahi, Bouraoui; Elhmaidi, Zakaria Oulad; Daniel, Valentin; Hanus, Tadeas; Arvinte, Roxana; Heintz, Alexandre; Mbeunmi, Alex Brice Poungoué; Diallo, Thierno Mamoudou; Arès, Richard; Boucherif, Abderraouf

doi:10.1109/pvsc48317.2022.9938839

Cited by 3 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…10,11 Porous Ge is fabricated by electrochemical etching and is potentially the lower cost route. 12,13 The GeON structure involves lithography and dry etching but provides easier control on the detachment layer and seed surface morphology. It also can be applied to any wafer doping and results in a perfectly non-porous seed.…”

Section: Introductionmentioning

confidence: 99%

“…Two routes of porous germanium are currently under development, based on random mesopores or patterned macropores. The former is usually referred to as “porous Ge” and the latter as “GON” or “GeON.” 10,11 Porous Ge is fabricated by electrochemical etching and is potentially the lower cost route 12,13 . The GeON structure involves lithography and dry etching but provides easier control on the detachment layer and seed surface morphology.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Wafer‐scale Ge epitaxial foils grown at high growth rates and released from porous substrates for triple‐junction solar cells

Depauw

Porret

Moelants

et al. 2022

Progress in Photovoltaics

View full text Add to dashboard Cite

Germanium is listed as a critical raw material, and for environmental and economic sustainability reasons, strategies for lower consumption must be implemented. A promising approach is Ge lift‐off concepts, which enable to re‐use the substrate multiple times. Our concept is based on the Ge‐on‐Nothing approach that is the controlled restructuring at high temperature of a macroporous Ge surface, forming a Ge foil weakly attached to its parent wafer. Its suitability as III–V epitaxy seed and support substrate has previously been demonstrated with proof‐of‐concept solar cells. This work focuses on bringing this concept to the next level, by upscaling the detachable area to a full 200‐mm wafer scale, increasing foil thickness for sufficient light absorption in the Ge bottom cell, and improving the control on the strength that is bonding the suspended foil to its parent. By introducing a new high growth‐rate epitaxy process from GeCl4, and by engineering the GeON structure to introduce pillars with ad hoc density and shape, we fabricated P‐type foils with tunable boron doping up to 15 μm in thickness and 11 cm × 11 cm in area, for which the detachment strength could be adapted to the stresses induced by the solar cell process steps. The surface roughness and the electrical and crystal qualities of these foils were inspected by AFM, SIMS, SRP, ECCI, and TEM to check the GeCl4‐based epitaxy conditions and to check that the ad hoc pillars were not introducing any damage. Small‐area triple‐junction lattice‐matched GaInP/GaInAs/Ge solar cells were fabricated on 7‐μm‐thick Ge foils with various pillar densities and on a standard reference Ge wafer. The III–V layer nucleation was virtually the same on both substrates and the solar cells on the GeON foils performed in the same way as the cells on the Ge wafer, albeit a small loss in short‐circuit current and open‐circuit voltage that can be attributed to the thickness reduction and absence of rear‐side passivation. We conclude that it is possible to gain control on the GeON detachability and upscale the concept to areas relevant for the space PV industry, proving that porous germanium is a serious candidate for replacement of bulk Ge wafers in view of a more sustainable multijunction solar cell process.

show abstract