Electric field analysis of 132kv EPDM insulator and correlation with ageing features

Tzimas, A.; Zachariades, Christos; Rowland, S. M.

doi:10.1109/eic.2013.6554235

Cited by 3 publications

(3 citation statements)

References 10 publications

(10 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Unbalanced field distribution along the creepage length can exaggerate and ultimately degrade and damage insulator surfaces as a result of partial discharges on the surface which usually take place before surface flashover [26]. A remote reading AC field meter EMF-A152 and a spherical probe EMF-A182 were used for the measurement of the E-field distribution for each insulator slab in both acidic and normal cold fog conditions.…”

Section: Effect Of Acidic and Clean Cold Fog On E-field Distributionmentioning

confidence: 99%

Risk Assessment of Failure of Outdoor High Voltage Polluted Insulators under Combined Stresses Near Shoreline

et al. 2017

View full text Add to dashboard Cite

Abstract:The aim of this paper is to investigate the various effects of climate conditions on outdoor insulators in coastal areas as a result of saline contamination under acidic and normal cold fog, determining significant electrical and physico-chemical changes on the insulator surface and considering the effect of discharge current, electric field distribution and surface roughness. To replicate similar conditions near the shoreline, experimental investigations have been carried out on insulation materials with the combined application of saline contamination and acidic or normal cold fog. The test samples included silicone rubber (SiR), ethylene propylene diene monomer (EPDM) and high-density polyethylene (HDPE), which were used as reference. The materials are of the same composition as those used in real-life outdoor high voltage insulators. All samples were aged separately in an environmental chamber for 150 h for various saline contaminations combined with acidic and normal cold fog, and were generated by means of the adopted experimental setup. This analysis represented conditions similar to those existing near the shoreline exposed to saline and acid spray during winter and early spring. Electric field and discharge current along polymeric samples were examined under acidic and normal cold fog. Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopic (SEM) were used to probe the physico-chemical changes on the samples surface and investigate the hydrophobicity recovery property after aging tests. Finally, a comparative study was carried out on polymeric samples before and after being exposed to the acidic and normal cold fog based on the results obtained from the experiment. Research data may provide references for the better prediction of surface degradation as well as for the better material coating and design of external insulation.

show abstract

Section: Effect Of Acidic and Clean Cold Fog On E-field Distributionmentioning

confidence: 99%

Risk Assessment of Failure of Outdoor High Voltage Polluted Insulators under Combined Stresses Near Shoreline

et al. 2017

View full text Add to dashboard Cite

show abstract

“…Electric field calculation along an outdoor insulator is considered to be one of the most reliable diagnostic tools. Experimental and numerical investigations have been carried out previously to locate defects in outdoor insulators using electric field calculations [28,29]. In this paper, various contamination and dry band conditions were considered to calculate the electric field distribution along the surface of the silicone rubber insulator.…”

Section: Electric Field Distributionmentioning

confidence: 99%

Effect of pollution severity and dry band location on the flashover characteristics of silicone rubber surfaces

et al. 2016

View full text Add to dashboard Cite

This paper investigates the flashover and ageing behavior of silicone rubber insulators under various contamination and dry band conditions. Effect of pollution severity, leakage distance and dry band location on the flashover characteristics of silicone rubber insulator was investigated. Flashover voltage and electric field distribution were measured under different pollution severity levels and dry band conditions. Effect of leakage distance on flashover voltage was also studied. Tests were carried out in a climate chamber and specific values of humidity and ambient temperature were used. A commercially available simulation package, COMSOL Multiphysics, was used to validate the experimental results. Electric field and potential along a silicone rubber sample were studied under different pollution severity and dry band conditions. Fourier transform infrared spectroscopy was used to analyze the chemical changes on the insulator surface and investigate the hydrophobicity recovery property of silicone rubber after flashover tests. The results of this study will further our knowledge regarding the flashover of silicone rubber outdoor insulators under contaminated and dry band conditions and could be used to improve the existing flashover models.

show abstract

“…The study of electric field distribution along polymeric insulators is very important for understanding the discharge mechanism and pollution flashover. Moreover, electric field study gives an indication of the possible damage and service life of insulator under contaminated conditions [14,15]. Electric field measurement could also be used as a diagnostic tool to detect invisible defects in polymer insulators.…”

Section: Introductionmentioning

confidence: 99%

Numerical Computation of Electric Field and Potential Along Silicone Rubber Insulators Under Contaminated and Dry Band Conditions

Ali

Nekahi

McMeekin

et al. 2016

3D Res

View full text Add to dashboard Cite

Electrical field distribution along the insulator surface is considered one of the important parameters for the performance evaluation of outdoor insulators. In this paper numerical simulations were carried out to investigate the electric field and potential distribution along silicone rubber insulators under various polluted and dry band conditions. Simulations were performed using commercially available simulation package Comsol Multiphysics based on the Finite Element Method (FEM). Various pollution severity levels were simulated by changing the conductivity of pollution layer. Dry bands of 2 cm width were inserted at the high voltage end, ground end, middle part, shed, sheath, and at the junction of shed and sheath to investigate the effect of dry band location and width on electric field and potential distribution. Partial pollution conditions were simulated by applying pollution layer on the top and bottom surface respectively. It was observed from the simulation results that electric field intensity was higher at the metal electrode ends and at the junction of dry bands. Simulation results showed that potential distribution is nonlinear in the case of clean and partially polluted insulator and linear for uniform pol-

show abstract

Electric field analysis of 132kv EPDM insulator and correlation with ageing features

Cited by 3 publications

References 10 publications

Risk Assessment of Failure of Outdoor High Voltage Polluted Insulators under Combined Stresses Near Shoreline

Risk Assessment of Failure of Outdoor High Voltage Polluted Insulators under Combined Stresses Near Shoreline

Effect of pollution severity and dry band location on the flashover characteristics of silicone rubber surfaces

Numerical Computation of Electric Field and Potential Along Silicone Rubber Insulators Under Contaminated and Dry Band Conditions

Contact Info

Product

Resources

About