Elastic behaviour of a model two-phase material

Hsieh, Chin-Lung; Tuan, Wei‐Hsing; Wu, Tung-Yu

doi:10.1016/j.jeurceramsoc.2004.02.002

Cited by 43 publications

(31 citation statements)

References 17 publications

(51 reference statements)

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Al 2 O 3 -NiAl composites containing 0 to 100 % NiAl are prepared by attrition milling and hot-pressing by Hsieh [2]. For the Al 2 O 3 rich composites, NiAl grains are distributed uniformly in the Al 2 O 3 matrix and NiAl grains are observed elongated within the Al 2 O 3 matrix.…”

Section: Resultsmentioning

confidence: 99%

“…Here, in this paper, we are dealing with bounding techniques, since we have many models which provide upper and lower bounds for elastic properties [3][4][5]16,21] to match the theoretical results with the experimental data [2].…”

Section: Resultsmentioning

confidence: 99%

“…We have chosen Al 2 O 3 -NiAl for comparison with our theoretical predictions, because elastic constants of Al 2 O 3 -NiAl system are available for complete range of composition [2].…”

Section: Resultsmentioning

confidence: 99%

“…To verify these relations, a comparison has been made between our calculated results and experimental data [2]. For this comparison, we consider Al 2 O 3 -NiAl composite, whose experimental data are available in the whole range of composition.…”

Section: Introductionmentioning

confidence: 96%

See 3 more Smart Citations

Elastic properties of Al2O3–NiAl: a modified version of Hashin–Shtrikman bounds

Upadhyay

Beniwal

Singh

2012

Continuum Mech. Thermodyn.

View full text Add to dashboard Cite

Section: Resultsmentioning

confidence: 99%

Section: Resultsmentioning

confidence: 99%

“…We have chosen Al 2 O 3 -NiAl for comparison with our theoretical predictions, because elastic constants of Al 2 O 3 -NiAl system are available for complete range of composition [2].…”

Section: Resultsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 96%

See 2 more Smart Citations

Elastic properties of Al2O3–NiAl: a modified version of Hashin–Shtrikman bounds

Upadhyay

Beniwal

Singh

2012

Continuum Mech. Thermodyn.

View full text Add to dashboard Cite

“…Ultrasonic measurements are a common tool used to determine the elastic properties of particulate materials (Ref [21][22][23]. In the present studies, the obtained sintered samples were assumed to be isotropic materials due to random orientation of the grains and distributed in the materialÕs volume.…”

Section: Methodsmentioning

confidence: 99%

Sintering Behavior and Mechanical Properties of NiAl, Al2O3, and NiAl-Al2O3 Composites

Chmielewski

Nosewicz

Pietrzak

et al. 2014

J. of Materi Eng and Perform

View full text Add to dashboard Cite

It is commonly known that the properties of sintered materials are strongly related to technological conditions of the densification process. This paper shows the sintering behavior of a NiAl-Al 2 O 3 composite, and its individual components sintered separately. Each kind of material was processed via the powder metallurgy route (hot pressing). The progress of sintering at different stages of the process was tested. Changes in the microstructure were examined using scanning and transmission electron microscopy. Metal-ceramics interface was clean and no additional phases were detected. Correlation between the microstructure, density, and mechanical properties of the sintered materials was analyzed. The values of elastic constants of NiAl/Al 2 O 3 were close to intermetallic ones due to the volume content of the NiAl phase particularly at low densities, where small alumina particles had no impact on the compositeÕs stiffness. The influence of the external pressure of 30 MPa seemed crucial for obtaining satisfactory stiffness for three kinds of the studied materials which were characterized by a high dense microstructure with a low number of isolated spherical pores.

show abstract