Effect of the TiC content on microstructure and thermal properties of Cu–TiC composites prepared by powder metallurgy

Buytoz, Soner; Dağdelen, Fethi; Islak, Serkan; Kök, Mediha; Kır, Durmuş; Ercan, Ercan

doi:10.1007/s10973-014-3900-6

Cited by 69 publications

(22 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…The reinforcement of TiC in Cu matrix composites can be prepared by several methods, such as powder metallurgy [6][7][8][9], friction stir casting processes [10,11], spray deposition, and high temperature synthesis [3]. Powder metallurgy is one of the most promising techniques.…”

Section: Introductionmentioning

confidence: 99%

“…Powder metallurgy is one of the most promising techniques. Several researchers have synthesized Cu x -Ti y C z -based composite by powder metallurgy treatment [6][7][8][9]12] and friction stir processing [10,11]. Many of them report the mechanical and tribological properties of Cu x -Ti y C z film, pointing out that the increasing TiC reinforcement improves the hardness and reduces the wear rates because of the good bonding between the TiC particles and the base metal [3,4,13].…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Surface Stoichiometry and Optical Properties of Cux–TiyCz Thin Films Deposited by Magnetron Sputtering

et al. 2019

View full text Add to dashboard Cite

Ternary carbide in metal matrix composites constitute a big challenge in the industry, and in this regard their surface treatment is one of the most important issues. Ternary carbide (CuxTiyCz, where x, y and z are integers) thin films are synthesized by magnetron sputtering and characterized with respect to the film depth. X-ray photoelectron spectroscopy (XPS) of Cu-2p and Ti-2p peaks shows the associated shake-up satellite peaks at a smaller film depth; the peak intensity is reduced at a higher depth. The relative intensity of Cu and Ti increases at a larger film depth. The optical band gap varies from 1.83 to 2.20 eV at different film depths.

show abstract

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Surface Stoichiometry and Optical Properties of Cux–TiyCz Thin Films Deposited by Magnetron Sputtering

et al. 2019

View full text Add to dashboard Cite

show abstract

“…Where H c is the hardness of composite, H m is the hardness of matrix, H t is the hardness of reinforcing element, and f m and f t are volume ratios of the matrix and reinforcing element, respectively. In addition, CNTs contributed to increasing of strength and hardness of a material by preventing dislocations' movement [26,27]. Moreover, it was argued that the hardness of the CNT composite samples increased because CNTs filled the micro-voids of the matrix particles [28].…”

Section: Resultsmentioning

confidence: 99%

The effect of CNT content and sintering temperature on some properties of CNT-reinforced MgAl composites

et al. 2017

Self Cite

View full text Add to dashboard Cite

Magnesium and its alloys are considered as an important material for modern light structures at the present time and therefore they have a wide area of usage especially in electronics, aircraft, and automotive industries. Its popularity increases further as a result of its production as a composite material. In this study, carbon nanotube (CNT) reinforced MgAl matrix composite materials were produced by using the hot pressing method. While 0.25 wt%, 0.50 wt%, 0.75 wt%, and 1.00 wt% CNT were added, 450°C, 500°C, and 550°C was selected as sintering temperatures. The effect of sintering temperature and amount of CNT on some properties of the composites was examined. Microstructure and phase composition of the materials were examined by using optical microscopy (OM), scanning electron microscope (SEM), X-ray diffraction (XRD), and energy-dispersive X-ray spectroscopy (EDS). The hardness of the composites was measured in Brinell. Relative densities of the materials were determined in accordance with Archimedes' principle. A dense and slightly porous structure was obtained based on both SEM images and density measurements. XRD analyses showed that there were Mg, Mg 17 Al 12 , and MgO phases in the composites. The reason for the absence of Al in graphics was that Al formed the solid solution by being dissolved in Mg. Also, the C peak could not be determined for CNT. The hardness of the composites increased with the increasing sintering temperature and CNT addition. The highest hardness value was measured as 88.45 HB10 with the addition of 1.00 wt% CNT at 550°C. Free distribution of CNT in the matrix caused this hardness increase.

show abstract

“…Recently, MMCs have been extensively investigated and implemented due to their promising advanced properties. Reinforcing particles, which are compatible with the matrix, are preferred in these composites [2][3][4][5][6][7][8]. Once again, nanoparticle-reinforced metal matrix composites are promising materials, and they are suitable for many applications [9].…”

Section: Introductionmentioning

confidence: 99%

Optimization by Using Taguchi Method of the Production of Magnesium-Matrix Carbide Reinforced Composites by Powder Metallurgy Method

Küçük

Elfarah

Islak

et al. 2017

Metals

Self Cite

View full text Add to dashboard Cite

Abstract:The aim of this study was to determine the optimum production parameters in the production of magnesium matrix carbide-reinforced composites by using the powder metallurgy method. The parameter levels maximizing density (%), hardness (HB10), and bending strength (MPa) values were found by using the Taguchi method. The type of reinforcement, the amount of reinforcement, the sintering time, the sintering temperature, additive type, and additive rate were selected as the production parameters. Since the production of Mg and its alloys by using casting methods is problematic, the hot pressing method, a powder metallurgy method, was preferred in this study. Ceramic-based carbide particles were used as reinforcing materials in Mg matrix composite materials. B 4 C, SiC, Mo 2 C, and TiC carbides were preferred as the carbide. Microstructure and phase composition of the produced materials was examined with scanning electron microscope (SEM), X-ray diffractogram (XRD) and X-ray energy dispersive spectrometry (EDS). The hardness of the materials was measured by using a Universal Hardness device. The relative densities of the materials were determined according to Archimedes' principle. The bending strength properties of the materials were determined by using the three-point bending test. The optimum conditions were a sintering temperature of 500 • C, sintering duration of 5 min, additive type of B 4 C and additive rate of 2.5%, and the results obtained at these conditions were found to be as follows; relative density of 98.74 (%), hardness of 87.16 HB10 and bending strength of 193.65 MPa. SEM images taken from the fracture surfaces showed that the carbides added to the matrix had a relatively homogeneous distribution. XRD analyses revealed that the matrix was oxidized very little, and no phase formation occurred between the matrix and the carbides. Carbide addition caused a distinct hardness increase by showing the effect of distribution strengthening in the matrix.

show abstract

Effect of the TiC content on microstructure and thermal properties of Cu–TiC composites prepared by powder metallurgy

Cited by 69 publications

References 22 publications

Surface Stoichiometry and Optical Properties of Cux–TiyCz Thin Films Deposited by Magnetron Sputtering

Surface Stoichiometry and Optical Properties of Cux–TiyCz Thin Films Deposited by Magnetron Sputtering

The effect of CNT content and sintering temperature on some properties of CNT-reinforced MgAl composites

Optimization by Using Taguchi Method of the Production of Magnesium-Matrix Carbide Reinforced Composites by Powder Metallurgy Method

Contact Info

Product

Resources

About