Abstract:Purpose
This paper aims to research the effect of different concentrations for Nd(NO3)3 and Ce(NO3)3 on the microstructures and corrosion resistance of Ni-W-P composite coatings through electroless plating method.
Design/methodology/approach
Scanning electron microscope, attached energy dispersive spectroscopy system and X-ray diffraction were used in this work. Meanwhile, the immersion test and electrochemical tests were used to characterize the corrosion behavior of the coating.
Findings
The coatings pre… Show more
“…Reducing the contact area between the substrate and electrolyte can effectively decrease the corrosion rate of Mg alloy (Li et al , 2023). Some methods, such as chemical conversion (Yang et al , 2022), anode oxidation (Wu et al , 2022a, 2022b), metal plating (Jia et al , 2022) and hydrothermal method (Rahimi et al , 2021), are widely used for Mg alloy protection. In recent years, the superhydrophobic surface (SHPS) has proven to be a promising strategy for enhancing the corrosion resistance of Mg alloy in aqueous environments.…”
Purpose
This paper aims to comprehensively review the preparation methods of superhydrophobic surfaces (SHPS) for corrosion protection of Mg alloy in recent years.
Design/methodology/approach
The preparation methods, wettability and corrosion resistance of SHPS on Mg alloy in the past three years are systematically described in this paper.
Findings
Two types of SHPS, including single-layer and multilayer coatings for corrosion protection of Mg alloy are summarized. Preparing multilayered coatings with multifunction is the current trend in developing SHPS on Mg alloy.
Originality/value
This paper reviewed the preparation methods and corrosion resistance of SHPS on Mg alloys. It provides a valuable reference for researchers to develop highly durable SHPS with excellent corrosion resistance for Mg alloys.
“…Reducing the contact area between the substrate and electrolyte can effectively decrease the corrosion rate of Mg alloy (Li et al , 2023). Some methods, such as chemical conversion (Yang et al , 2022), anode oxidation (Wu et al , 2022a, 2022b), metal plating (Jia et al , 2022) and hydrothermal method (Rahimi et al , 2021), are widely used for Mg alloy protection. In recent years, the superhydrophobic surface (SHPS) has proven to be a promising strategy for enhancing the corrosion resistance of Mg alloy in aqueous environments.…”
Purpose
This paper aims to comprehensively review the preparation methods of superhydrophobic surfaces (SHPS) for corrosion protection of Mg alloy in recent years.
Design/methodology/approach
The preparation methods, wettability and corrosion resistance of SHPS on Mg alloy in the past three years are systematically described in this paper.
Findings
Two types of SHPS, including single-layer and multilayer coatings for corrosion protection of Mg alloy are summarized. Preparing multilayered coatings with multifunction is the current trend in developing SHPS on Mg alloy.
Originality/value
This paper reviewed the preparation methods and corrosion resistance of SHPS on Mg alloys. It provides a valuable reference for researchers to develop highly durable SHPS with excellent corrosion resistance for Mg alloys.
“…The composite plating is prepared by co-depositing metals with insoluble solid particles, inert particles, fibers, etc. (Jia et al , 2022). Among them, the nanocomposite plating prepared by adding nanoscale (less than 100 nm) inorganic particles to the plating has prominent properties so that it was used in a wide range of fields (Fathi et al , 2021; Safavi and Rasooli, 2019).…”
Purpose
The purpose of this study is to reveal the effect of nano-Al2O3 particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of Co–P–xAl2O3 nanocomposite plating.
Design/methodology/approach
The kinetics and properties of Co–P–xAl2O3 nanocomposite plating prepared by electroplating were investigated by electrochemical measurements, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Vickers microhardness measurement, SRV5 friction and wear tester and atomic force microscopy.
Findings
A 12 g/L nano-Al2O3 addition in the plating solution can transform the nucleation/growth kinetics of the plating from the 3D progressive model to the 3D instantaneous model. The microhardness of the plating increased with the increase of nano-Al2O3 content in plating. The wear resistance of the plating did not adhere strictly to Archard’s law. An even and denser corrosion product film was generated due to the finer grains, with a high corrosion resistance.
Originality/value
The effect of different nano-Al2O3 addition on the nucleation/growth kinetics and properties of Co–P–xAl2O3 nanocomposite plating was investigated, and an anticorrosion mechanism of Co–P–xAl2O3 nanocomposite plating was proposed.
“…At present, the electrodeposition of Zn–Ni alloy coatings in aqueous solution is a mature technology that is widely used in industrial production (Bahadormanesh et al , 2017; Beheshti et al , 2020. Shekhanov et al , 2020; Abou-Krisha, 2005; Farooq et al , 2022; Roventi et al , 2015; Jia et al , 2022). However, Zn–Ni alloys are usually deposited in alkaline and acidic chloride solutions, and after deposition, the resulting waste liquid is often toxic and corrosive.…”
Purpose
The purpose of this paper is to study the effect of temperature on Zn–Ni alloys in ChCl–Urea.
Design/methodology/approach
Based on cyclic voltammetry experiments, the deposition behavior and kinetics of the Zn–Ni alloy are studied. The nucleation process of the Zn–Ni alloy is studied in detail via chronoamperometry experiments. The effects of the deposition temperature on the microstructure, Ni content and phase composition of Zn–Ni alloy coatings are investigated via scanning electron microscopy and X-ray diffraction (XRD) combined with classical thermodynamics.
Findings
The results show that with increasing temperature, the reduction peak shifts toward a more positive electric potential, which is beneficial for the co-electric deposition process, and the diffusion coefficient is estimated. With increasing temperature, the nucleation process of the Zn–Ni alloy becomes a three-dimensional instantaneous nucleation, the typical kinetic parameters are determined using the standard 3D growth proliferation control model and the Gibbs free energy is estimated. The Zn–Ni alloy coatings are prepared via normal co-deposition. With increasing temperature, the degree of crystallinity increases, the coating gradually becomes uniform and compact and the XRD peak intensity increases.
Originality/value
The nucleation process of the Zn–Ni alloy at different temperatures is analyzed. The diffusion coefficient D and Gibbs free energy are calculated. The contribution of the three processes at different temperatures is analyzed. The effect of temperature on the morphology of the Zn–Ni alloy coatings is studied.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.