Effect of mill type on the size reduction and phase transformation of gamma alumina

Chauruka, Sandra; Hassanpour, Ali; Brydson, R.; Roberts, Kevin J.; Ghadiri, Mojtaba; Stitt, H.

doi:10.1016/j.ces.2015.06.004

Cited by 118 publications

(64 citation statements)

References 22 publications

(24 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Therefore, it appears that the transformation from γ to α-Al 2 O 3 occurred with the absence of these transitional changes as showed previously by A. Tonejc [2]. Recently, other researchers have shown similar results in the milling of commercial powders of γ-Al 2 O 3 and boehmite by means of planetary ball milling [3] [4]. The results reported in our work show that SPEX mechanical milling is highly effective in the reduction and homogenization of particle size.…”

supporting

confidence: 75%

Solid State Transition from γ to α-Al₂O₃ Induced by SPEX Mechanical Milling

et al. 2017

View full text Add to dashboard Cite

The high energy ball milling is an easy and low cost technique that has been highly used in the processing of powder materials. This technique has demonstrated to be effective in the synthesis of new compounds, formation of solid solutions, production of nanostructured materials, activation of powders and homogenization of phases [1]. In this study we report the use of the SPEX mechanical milling to synthesize α-Al 2 O 3 from γ-Al 2 O 3 . The γ-Al 2 O 3 was obtained by the calcination of pseudoboehmite at 500 ºC for 2 h. The pseudoboehmite was synthesized from aluminum sulfate hydrated (Al 2 (SO 4 ) 3 • xH 2 O) and anhydrous ammonia (NH 3 ). The powders of γ-Al 2 O 3 were poured into a steel stainless jar in batches of 10 gr and milled for times of 5 and 10 h. No control agent or any other additional component was added during the milling process. The mechanical treatment was performed at room temperature and under atmospheric conditions. The as milled powders were analyzed by XRD and SEM. Figure 1(a, b and c) shows the effect of the mechanical milling in the particle size and distribution. Figure 1a displays the raw powders of γ-Al 2 O 3 that are composed by big particles of irregular shape. The particles after 5 h (1b) adopted a round shape and a light decrease of particle size in comparison to the raw powder. Short times of milling demonstrated to be effective in the reduction and homogenization of the particle size. The Figure 2 shows the XRD analysis of the powders before and after milling treatment. These analyses show that the SPEX mechanical milling supplies enough energy to achieve the beginning of the transformation from γ to α-Al 2 O 3 . After 10 h of milling, new reflections were detected and assigned to the reflections (-216), (-224), (-213), (-114) and (-112) in good agreement to the XRD pattern COD 1000032. No evidence of contamination generated during the mechanical milling was observed. Moreover, the presence of the intermediate phases δ and θ was not detected. Therefore, it appears that the transformation from γ to α-Al 2 O 3 occurred with the absence of these transitional changes as showed previously by A. Tonejc [2]. Recently, other researchers have shown similar results in the milling of commercial powders of γ-Al 2 O 3 and boehmite by means of planetary ball milling [3][4]. The results reported in our work show that SPEX mechanical milling is highly effective in the reduction and homogenization of particle size. Moreover, it has been demonstrated that SPEX milling is successful to achieve the transformation from γ-Al 2 O 3 to α-Al 2 O 3 at room temperature without producing any significant level of contamination.

show abstract

supporting

confidence: 75%

Solid State Transition from γ to α-Al₂O₃ Induced by SPEX Mechanical Milling

et al. 2017

View full text Add to dashboard Cite

show abstract

“…At temperature range of 500 °C and 700 °C, the -Al2O3 material was formed [5,6], the annealing at 750 °C exhibited the Al2O3 [7], and the Al2O3 were formed between 900 °C and 1000 °C [6,8]. The stable -Al2O3 can be formed at 1100 °C and above [1,5,9].…”

Section: Introductionmentioning

confidence: 82%

Influence of annealing temperature on the phase transformation of Al2O3

Mahat

Mastuli

Kamarulzaman

2016

AIP Conference Proceedings

View full text Add to dashboard Cite

“…However, b 12 , b 13 are not meaningful since they are smaller than the value of a Student's coefficient that is equal to 1 for the number of degrees of freedom f=(m-1)N=(3-1)8=16 and a significance level of 0.05t=2.12.…”

Section: Results Of Research Into Quality Of the Shredded Bee Pollenmentioning

confidence: 99%