Effect of geometry and hybrid adhesive on strength of finger joints of<i>Pinus elliottii</i>subject to humidity and temperature

Messmer, Nigel Roderick; Anjos, Erick Gabriel Ribeiro dos; Guerrini, Lília M.; Oliveira, Maurício P.

doi:10.1080/00218464.2017.1319281

Cited by 7 publications

(2 citation statements)

References 25 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This necessitates a careful examination of the adhesive properties of materials used in additive manufacturing. Factors such as adhesive durability, bonding strength, and energy absorption can vary under different temperature conditions (Messmer et al, 2018;Yamazaki et al, 2020). Achieving reliable and robust adhesion is crucial for ensuring the structural integrity and performance of assembled components.…”

Section: Introductionmentioning

confidence: 99%

Temperature-Dependent Debonding Resistance of 316 Stainless Steel, Inconel 625, and Ti-6AL-4V Alloys

Arıkan

2023

Black Sea Journal of Engineering and Science

View full text Add to dashboard Cite

This study investigates the temperature-dependent debonding properties of 316 Stainless Steel (SS), Inconel 625, and Ti-6AL-4V alloys in additive manufacturing using the finite element method. The analysis reveals notable relations between in mechanical properties and debonding resistance among these materials. Inconel 625 demonstrates superior performance at elevated temperatures, while SS and Ti-6AL-4V alloys show earlier degradation. Regarding debonding resistance, Inconel 625 performs comparably to SS and Ti-6AL-4V alloys, with Ti-6AL-4V exhibiting consistent resistance below 500°C. SS, however, experiences a rapid loss of debonding resistance at lower temperatures. These findings provide valuable insights for material selection and design optimization in additive manufacturing. Further research can expand our understanding of these materials' behavior under different temperature regimes using the finite element method, enhancing their application potential.

show abstract

Section: Introductionmentioning

confidence: 99%

Temperature-Dependent Debonding Resistance of 316 Stainless Steel, Inconel 625, and Ti-6AL-4V Alloys

Arıkan

2023

Black Sea Journal of Engineering and Science

View full text Add to dashboard Cite

show abstract

“…Tran presented an experimental investigation on full-scale glued solid oak beams for structural purposes (Tran, Oudjene, & Méausoone, 2016). Other works (Ammann et al, 2016;Messmer, Anjos, Guerrini, & Oliveira, 2017 and others) focus on glued joints, effect of adhesive compositions, degree of adhesive penetration into timber structure, and timber moisture on the formation of glued joints and their stability, or the effect of surface roughness on gluing. Lara-Bocanegra investigated the influence of geometric and material parameters, assembly pressure and failure modes on finger-joint bending strength of eucalyptus hardwood (Lara-Bocanegra, Majano-Majano, Crespo & Guaita, 2017).…”

Section: Introductionmentioning

confidence: 99%

Experimental research on load bearing capacity of adhesively jointed beech timber lamellas

Šuhajdová

Novotný

Pěnčík

et al. 2019

Modern Building Materials, Structures and Techniques (MBMST)

View full text Add to dashboard Cite

The aim of this work was to verify behavior of a beech timber finger-joint in local conditions in the Central Europe. The samples were produced with a glued joint with the finger length of 23 mm according to standard ČSN EN 14 080. Commonly used polyurethane adhesive for production of engineered wood products in the Czech Republic was used. The samples were loaded by destructive four-point bending tests according to standard ČSN EN 408, and the achieved bending strength was statistically evaluated and compared with results of non-glued samples. The results showed that bending strength of lamellas with a finger-joint reached about 65% of the strength of samples without a joint, and the failure of lamellas occurred in most cases at the joint.

show abstract

Surfactant-free hybrid adhesives based on poly(vinyl acetate) and commercial montmorillonite nanoclays

2021

View full text Add to dashboard Cite

Effect of geometry and hybrid adhesive on strength of finger joints ofPinus elliottiisubject to humidity and temperature

Cited by 7 publications

References 25 publications

Temperature-Dependent Debonding Resistance of 316 Stainless Steel, Inconel 625, and Ti-6AL-4V Alloys

Temperature-Dependent Debonding Resistance of 316 Stainless Steel, Inconel 625, and Ti-6AL-4V Alloys

Experimental research on load bearing capacity of adhesively jointed beech timber lamellas

Surfactant-free hybrid adhesives based on poly(vinyl acetate) and commercial montmorillonite nanoclays

Contact Info

Product

Resources

About