Development and Characterization of a Modified Ring Shaped Force Transducer

Kumar, Harish; Pardeep,; Kaushik, M.; Kumar, Anil

doi:10.1007/s12647-014-0118-9

Cited by 11 publications

(13 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Taking the objective of development of simple shaped precision force transducers, some researchers have been reported regarding the development of square ring shaped force transducer, hexagonal ring shaped force transducer and extended octagonal ring shaped force transducer (O'Dogherty 1996, Kumar and Sharma 2012a,b, Kumar et al 2013, 2015. Hence, for better precision and reliability, the present paper attempts to development of elliptical shaped force transducers.…”

Section: Introductionmentioning

confidence: 94%

“…Though some of the modifications of ring shaped force transducers like square ring shaped force transducer and hexagonal ring shaped force transducer have been demonstrated for static force measurement related applications, but their uncertainty of measurement is found up to 0.10 % (k = 2), and these developments are in their preliminary phases too. Their suitability over the wide range of force measurement related applications is still to be justified (Kumar, et al 2015).…”

Section: Analytical Studymentioning

confidence: 99%

“…The different factors pertaining to the uncertainty of measurement of the force transducer are listed below (Kumar et al, 2015). This uncertainty has been computed using Eqs.…”

Section: Calibration Proceduresmentioning

confidence: 99%

“…4. A realistic strain gauged elliptical shaped force transducer 50 kN dead weight force machine(Kumar et al, 2015)…”

mentioning

confidence: 99%

See 3 more Smart Citations

Investigations on metrological characterization of elliptical shaped force transducers for precision force measurement

Kumar¹,

Kaushik²,

Pardeep³

et al. 2015

10.5267/j.esm

Self Cite

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 94%

Section: Analytical Studymentioning

confidence: 99%

See 2 more Smart Citations

Investigations on metrological characterization of elliptical shaped force transducers for precision force measurement

Kumar¹,

Kaushik²,

Pardeep³

et al. 2015

10.5267/j.esm

Self Cite

View full text Add to dashboard Cite

“…An octagonal elliptical ring based milling dynamometer was designed, developed and analyzed for cutting force measurement and the proposed design had better performance and it was suitable for small to medium size industries for milling force measurement [11]. Modified ring shaped force transducer for measuring the cutting force up to 20 kN with an uncertainty of ± 0.10 % was designed and developed [30][31][32]. High performance force and torque sensor for measuring the turning force [33,34] and milling torque [35] was developed using strain gauge.…”

Section: Introductionmentioning

confidence: 99%

Design, development, calibration, and testing of indigenously developed strain gauge based dynamometer for cutting force measurement in the milling process

Mohanraj¹,

Shankar²,

Rathanasamy³

et al. 2020

JMES

View full text Add to dashboard Cite

In this work, a milling dynamometer based on strain gauge with an octagonal and square ring was designed and tested. Strain gauges were attached with the mechanical rings to detect the deformation, during the machining process. Wheatstone bridge circuit was equipped with gauges to acquire the strain as voltage owing to the deformation of mechanical rings when machining takes place. The finite element analysis (FEA) was used to identify the location of maximum deformation and stress. The direction of rings and location of gauges were decided to increase the sensitivity and decrease the cross-sensitivity. Then, the cutting force was acquired through NI 6221 M series data acquisition (DAQ) card. The dynamometer had undergone a cycle of tests to verify its static and dynamic characteristics. The metrological characterization was performed according to the calibration procedure based on ISO 376 – 2011 standard. The cutting force was measured with both the dynamometers through milling experiments based on Taguchi’s L9 orthogonal array and the results were recorded. The measured cutting force varied from 300 N to 550 N. The obtained results depicted that low-cost milling dynamometer was reliable to measure the three component machining force. Overall, the square ring based dynamometer provides the better static and dynamic characteristics in terms of linearity, cross-sensitivity (4%), uncertainty (0.054%), and natural frequency (362.41 rev/s).

show abstract

Design and Development of Trapezoidal-shaped Transducer for Industrial and Scientific Applications

Saxena,

Kumar

2023

MAPAN

View full text Add to dashboard Cite

Development and Characterization of a Modified Ring Shaped Force Transducer

Cited by 11 publications

References 6 publications

Investigations on metrological characterization of elliptical shaped force transducers for precision force measurement

Investigations on metrological characterization of elliptical shaped force transducers for precision force measurement

Design, development, calibration, and testing of indigenously developed strain gauge based dynamometer for cutting force measurement in the milling process

Design and Development of Trapezoidal-shaped Transducer for Industrial and Scientific Applications

Contact Info

Product

Resources

About