Design of the Liquid Volume Meter Device Using Ultrasonic Waves Based on Microcontroller

Zakaria, Diky; Gunawan, Teddy Surya; Somantri, Yoyo; Abdullah, Ade Gafar; Widiaty, Isma; Nandiyanto, Asep Bayu Dani; Amelia, Nia; Juhana, A; Arasid, W

doi:10.1088/1757-899x/384/1/012019

Cited by 6 publications

(6 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…An average error of 6 test points 5, 10, 15, 20, 25, and 30 cm was 0.52% with a standard deviation 0.01 cm. It was showed that error value using the SRF05 sensor [1,5] smaller than the HCSR04P sensor in Table 1 as 0.62%. However, both sensors show the same result of the standard deviation.…”

Section: Resultsmentioning

confidence: 94%

“…The following data from ultrasonic sensor calibration using a standard steel ruler in Table 1. In [1,5], calibration data were obtained using a steel ruler for SRF05 ultrasonic sensor. An average error of 6 test points 5, 10, 15, 20, 25, and 30 cm was 0.52% with a standard deviation 0.01 cm.…”

Section: Resultsmentioning

confidence: 99%

“…There are several previous studies that designed the tank liquid level monitoring system for the buried tank. The monitoring system designed by using microcontroller-based ultrasonic waves [5][6][7], the use of ThingSpeak as the internet of things server [8][9] as well as IP address by using a Wifi module NodeMCU [10][11][12]. Thus, this study will be designed as a system of monitoring the liquid level in the buried tank based on the internet of things, thus the management of fuel supply in the petrol station becomes more efficient and effective.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Design an Internet of Things Simulator of Fluid Volume Monitoring System for Petrol Station Underground Tank

Hidayanti¹

2020

IJST

View full text Add to dashboard Cite

Objectives: This study aims to design an internet of things simulator of fluid volume monitoring system. Methods: The method used in this research includes simulator design and simulator testing. Monitoring system using an ultrasonic sensor, nodeMCU, ThingSpeak, and Virtuino. The value of ultrasonic sensors will be processed in the NodeMCU program resulting liquid level in the buried tank then sent through the internet to ThingSpeak. Findings: The result of monitoring the liquid level in a buried petrol station simulator uses ultrasonic sensor HCSR04P and NodeMCU v.1.0 from 08.00 pm to 02.00 am displayed on the site ThingSpeak with value 17.42 L.Setting alarm on Virtuino at 50% of maximum volume of 8.8 L. The experimental results the volume of fluid reduction 8.09 L has managed to activate alarm on the application Virtuino. Applications: This internet of things simulator of fluid volume monitoring system applicated for the petrol station underground tank.

show abstract

Section: Resultsmentioning

confidence: 94%

Section: Resultsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Design an Internet of Things Simulator of Fluid Volume Monitoring System for Petrol Station Underground Tank

Hidayanti¹

2020

IJST

View full text Add to dashboard Cite

show abstract

“…Pemilihan sensor ultrasonik disebabkan kemampuan sensor untuk mendeteksi jarak tanpa harus bersinggungan dengan benda yang diukur [8]. Disamping itu akurasi sensor ultrasonik relatif bagus, sehingga cocok digunakan untuk alat yang dirancang [9], [10]. Untuk menggerakkan sistem mekanik alat penampung buku digunakan motor DC berdaya rendah [11] [12].…”

Section: Pendahuluanunclassified

Rancang Bangun Alat Penampung Buku Berbasis Arduino Pada Sistem Pengembalian Buku Layanan Mandiri

Naf’an

2021

JSisfotek

View full text Add to dashboard Cite

This study aims to design and create a book container in a self-service book return system at the Andalusia Library & Knowledge Center UPI "YPTK" Padang. Currently, the self-service book return system is carried out through a book drop machine. This book container is designed to complement the book drop machine. The returned book is inserted into the slanted gap so that it can slide into the book container. When the book container is empty, the base is at the upper limit position. If a book is entered, the base will automatically drop according to the thickness of the book. And so on, until it is full and the buzzer is active. Thus, it is hoped that book damage can be prevented due to the book falling too far down. The system is designed using ultrasonic sensors to detect upper and lower limits, a DC motor to move the base down according to the thickness of the book. After testing, the book container works well and is able to withstand loads of up to 22 kg with the number of books between 30 and 50 depending on the size of the book. The DC motor is able to move the book container when the load is maximum. The sensor can detect the thickness of the book, the upper and lower limits and the buzzer can activate when the book is full. Thus, this tool can be used to support the book drop in the self-service book return system.

show abstract

Section: Pendahuluanunclassified

Rancang Bangun Alat Penampung Buku Berbasis Arduino pada Sistem Pengembalian Buku Layanan Mandiri

Naf’an

2021

JSisfotek

View full text Add to dashboard Cite

This study aims to design and create a book container in a self-service book return system at the Andalusia Library & Knowledge Center UPI YPTK Padang. Currently, the self-service book return system is carried out through a book drop machine. This book container is designed to complement the book drop machine. The returned book is inserted into the slanted gap so that it can slide into the book container. When the book container is empty, the base is at the upper limit position. If a book is entered, the base will automatically drop according to the thickness of the book. And so on, until it is full and the buzzer is active. Thus, it is hoped that book damage can be prevented due to the book falling too far down. The system is designed using ultrasonic sensors to detect upper and lower limits, a Direct Current (DC) motor to move the base down according to the thickness of the book. After testing, the book container works well and is able to withstand loads of up to 22 kg with the number of books between 30 and 50 depending on the size of the book. The DC motor is able to move the book container when the load is maximum. The sensor can detect the thickness of the book, the upper and lower limits and the buzzer can activate when the book is full. Thus, this tool can be used to support the book drop in the self-service book return system.

show abstract

Design of the Liquid Volume Meter Device Using Ultrasonic Waves Based on Microcontroller

Cited by 6 publications

References 1 publication

Design an Internet of Things Simulator of Fluid Volume Monitoring System for Petrol Station Underground Tank

Design an Internet of Things Simulator of Fluid Volume Monitoring System for Petrol Station Underground Tank

Rancang Bangun Alat Penampung Buku Berbasis Arduino Pada Sistem Pengembalian Buku Layanan Mandiri

Rancang Bangun Alat Penampung Buku Berbasis Arduino pada Sistem Pengembalian Buku Layanan Mandiri

Contact Info

Product

Resources

About