Design and Implementation of Z-Source Inverter by Simple Boost Control Technique for Laboratory Scale Micro-Hydro Power Plant Application

Ariefianto, Rizki Mendung; Aprilianto, Rizky Ajie; Suryoatmojo, Heri; Suwito, Suwito

doi:10.15294/jte.v13i2.31884

Cited by 8 publications

(8 citation statements)

References 30 publications

(42 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The voltage on the load side is larger than the PV voltage in solar harvesting energy applications. It implies that the step-up voltage procedure must be carried out, and the boost converter becomes one of the several topologies that may be chosen and included into an MPPT [32], [36], [55], [58], [78], [81], [82], [93], [102], [103], [110], [132], [135], [258], [264], [276], [278], [286]- [300]. The boost converter is the most popular option, and it has been manufactured by industry [295].…”

Section: Boost Convertermentioning

confidence: 99%

See 1 more Smart Citation

Modernisation of DC-DC converter topologies for solar energy harvesting applications: A review

Sutikno

Purnama

Aprilianto

et al. 2022

IJEECS

View full text Add to dashboard Cite

Solar photovoltaic (PV) power generation has become increasingly important as a renewable source of energy due to the many benefits it offers. These benefits include the ease with which it can be allocated; the absence of noise; the longer life; the absence of pollution; the shorter amount of time required for installation; the high mobility and portability of its parts; and the capability of its output power to meet peak load requirements. DC-DC converters are typically incorporated into solar energy harvesting systems because they allow for the more efficient exploitation of solar cells. One of the difficulties is in the selection of a suitable converter since this has an effect on the operation of the PV system. This study discusses the modernisation of several different DC-DC converter topologies for solar energy harvesting systems. Some of these topologies are boost, buck-boost, single-ended primary-inductance converter (SEPIC), Cuk, and flyback. The topologies have been compared so that detailed information on the complexity of the hardware, the cost of implementation, the efficiency of the energy transfer elements, the tracking efficiency, and the efficiency of the converters can be provided. This paper will be useful as a handy reference in choosing the best converter topology for solar energy harvesting applications.

show abstract

Section: Boost Convertermentioning

confidence: 99%

“…The Z-source comprises two identical inductors and two capacitors, in which the modernization of this configuration has been fluent and conducted to achieve better performance [87], [102], [122], [166], [291], [300], [314], [366]- [368]. A modified Z-source DC-DC converter is proposed by [367].…”

Section: Z-source Convertermentioning

confidence: 99%

Modernisation of DC-DC converter topologies for solar energy harvesting applications: A review

Sutikno

Purnama

Aprilianto

et al. 2022

IJEECS

View full text Add to dashboard Cite

show abstract

“…There are much research concerning the control of ZSI and its improvement. [9][10][11][12][13] In Dave et al, 9 the online parametric investigation has been achieved using online condition monitoring the investigation of this parameter can help to predict the maximum system life span. However, the control method did not give any methodology for the compensation transfer function.…”

Section: Introductionmentioning

confidence: 99%

Refine control methodology and implementation of capacitor voltage control for improved switched inductor Z‐source inverter

Ismeil

Orabi

Ahmed

et al. 2023

Circuit Theory & Apps

View full text Add to dashboard Cite

SummaryNowadays, Z‐source inverter (ZSI) has received several attentions compared to other power converters owing to their simplicity and reliability. In this paper, a refine control methodology of capacitor voltage control is presented based on third‐order small signal analysis. The proposed control is applied to the improved switched inductor ZSI (ISL‐ZSI). Proportional, integral, and derivative controller (PID) is adopted due to their capability to operate with large operation levels, reliable operation, and cheaper implementation. In addition, the function of this control can be achieved even with incomplete system data or parameters variations. ISL‐ZSI has been presented because of its advantages such as the high gain of direct current voltage, low voltage stress for both the Z‐network and the inverter bridge switches, and ensuring good soft starting. In addition, the inrush current has been removed based on its configuration. The proposed control is validated by both experimental and simulation results under input voltage change, load change, and steady‐state operations using DSP F28335 and MATLAB SIMULINK Real‐Time Workspace.

show abstract

“…Planning in saving the budget can be applied to a design. Moreover, optimization can be used to an appropriate model design [1]. Accurate design plays an essential role in the development of control systems knowledge.…”

Section: Introductionmentioning

confidence: 99%

Performance Evaluation of Two System Models for a MIMO System to Hover the Bicopter Unmanned Aerial Vehicle

Prakosa

Agmal

Kurniawan

et al. 2022

Jurnal Teknik Elektro

View full text Add to dashboard Cite

Building unmanned aerial vehicle (UAV) control system models are highly challenging due to multiple inputs and multiple outputs (MIMO). Not only does it have various angular position outputs such as roll, yaw, and pitch, but also flight control has more than one input; for instance, a bicopter has dual rotors. More rotors have more complex model. The hover condition has a zero resultant force which can be utilized to design a system model. On the other hand, an attractive identification system method is applied to develop the design. This research aims to evaluate the performance of two MIMO design on bicopter between methods based on the hover principle and identification technique. Experimental validation by employing bicopter simulator is an excellent strategy to fulfil this purpose. The results of the investigation of the experiment showed that the identification model was more accurate than the hover design, particularly regarding the overshot phenomenon and error. In addition, the hover principle tended to build ideal model because it did not include the dynamic, uncertainty and nonlinear conditions in aeroplane control design. Although the identification system was complicated because it previously needed to measure the input and output values, it performed closer to the actual experiment. It performed more satisfactory overshoot values compared with the experimental validation than the hover model by 1°, 3°, and 8° in roll, pitch, and yaw angles, respectively.

show abstract

Design and Implementation of Z-Source Inverter by Simple Boost Control Technique for Laboratory Scale Micro-Hydro Power Plant Application

Cited by 8 publications

References 30 publications

Modernisation of DC-DC converter topologies for solar energy harvesting applications: A review

Modernisation of DC-DC converter topologies for solar energy harvesting applications: A review

Refine control methodology and implementation of capacitor voltage control for improved switched inductor Z‐source inverter

Performance Evaluation of Two System Models for a MIMO System to Hover the Bicopter Unmanned Aerial Vehicle

Contact Info

Product

Resources

About