Density and surface tension polyterms of lead-based alloys

Kashezhev, A. Z.; Kutuev, R. A.; Ponezhev, M. Kh.; Созаев, В. А.; Khasanov, A. I.

doi:10.3103/s1062873812070179

Cited by 9 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The density values in the Pb-Ca system are described by the linear dependence ( Figure 1). Thus, our data identified the temperature posing action in the Pb -Ca system [6]. Surface properties of liquid alloys of the Pb-Ni system have not been studied yet.…”

Section: IIImentioning

confidence: 73%

Surface Properties of Lead and Zinc Alloys

Kutuev¹

2018

Proceedings of the International Symposium “Engineering and Earth Sciences: Applied and Fundamental Research” (ISEES 2018)

View full text Add to dashboard Cite

show abstract

Section: IIImentioning

confidence: 73%

Surface Properties of Lead and Zinc Alloys

Kutuev¹

2018

Proceedings of the International Symposium “Engineering and Earth Sciences: Applied and Fundamental Research” (ISEES 2018)

View full text Add to dashboard Cite

show abstract

“…Lead-bismuth melts are widely used as coolants in nuclear reactors [16,17]. Therefore, owing to its practical significance, the properties of this system have been studied more completely [2,18,19]. The obtained experimental data on the ST concentration dependence of these melts show that the ST isotherm of this system is characterized by an almost linear dependence, which is not often found among binary metallic systems (Fig.…”

Section: Mj/m2mentioning

confidence: 98%

Concentration Dependence of the Surface Tension of Three and Four-Component Systems with Peculiarities in the Surface Tension Isotherms of Lateral Binary Melts

Dadashev

Kutuev

2021

MSF

View full text Add to dashboard Cite

The experimental study results of the melts concentration dependence of the surface tension of the four-component indium-tin-lead-bismuth system and its constituent binary systems of indium-tin, indium-lead, indium-bismuth, tin-lead, tin-bismuth, lead-bismuth are presented in the paper. It is shown that the concentration dependence of the melts surface tension of the In-Sn-Pb-Bi four-component system can be predicted from the data on ST (surface tension) values of lateral binary systems. Features in the ST isotherms in the form of a minimum are observed only in the indium-tin lateral system from all lateral binaries. A distinctive feature of the detected minimum is that the minimum depth slightly exceeds the experimental error. Therefore, in addition to the fact that the area of average compositions was studied more thoroughly, we carried out the surface tension measurements by two independent methods. The experimental data obtained by both methods coincide within the experimental error and indicate the extremum availability on ST isotherms. Thus, ST experimental studies by two independent methods confirmed the presence of a flat minimum on ST isotherms of the indium-tin binary system increasing the reliability of the obtained data. The obtained outcomes and their comparison with experimental data have shown that the considered models for predicting surface properties based on data due to similar properties of lateral binary systems adequately reflect the experimental dependences. However, the prediction model based on Kohler's method of excess values describes the experimental curves more accurately.

show abstract

Measurement principles for room temperature liquid and fusible metals’ surface tension

Handschuh‐Wang

Wang

et al. 2023

Surfaces and Interfaces

View full text Add to dashboard Cite

Density and surface tension polyterms of lead-based alloys

Cited by 9 publications

References 0 publications

Surface Properties of Lead and Zinc Alloys

Surface Properties of Lead and Zinc Alloys

Concentration Dependence of the Surface Tension of Three and Four-Component Systems with Peculiarities in the Surface Tension Isotherms of Lateral Binary Melts

Measurement principles for room temperature liquid and fusible metals’ surface tension

Contact Info

Product

Resources

About