Cr-doped U3Si2 composite fuels under steam corrosion

Wang

et al. 2022

Polymers

Studies show that the dispersion of silica in the mixing process is an important factor affecting the wear of the mixing chamber. As the most important mixing equipment, the long operational life of the internal mixer will cause wear in the rotor and chamber of the internal mixer. This wear increases the gap between the rotor and chamber of the internal mixer, reduces the mixing performance, weakens the dispersion of packing, and adversely affects the quality of the rubber produced. Therefore, it is important to investigate the metal wear in the mixing process. This article examines the effect of the addition of different amounts of silane coupling agents on metal friction and wear during the mixing process. The silane coupling agent has two functions. The first is to make the surface of the silica hydrophobic, enabling it to combine the inorganic matrix of the silica with the organic matrix of the rubber; the second is to inhibit the aggregation of the silica in the rubber. In the present study, we examine (1) the influence of different formulations on the friction and wear of the metal in the mixing chamber from the perspective of formulation technology, and (2) the correlation between corrosion wear and abrasive wear. It is found that a rubber compound with 6 phr of TESPT has the lowest metal wear and that adding more TESPT does not affect the degree of metal wear. As the amount of TESPT increases, the proportion of abrasive wear decreases, while the proportion of corrosive wear increases, reaching a maximum of 20.7%. In our study we found that abrasive wear is the predominant wear mechanism of a rubber compound on metal. In contrast, the corrosive wear caused by high-temperature water vapor still occupies a large proportion of the total wear. Therefore, improving silica dispersion and reducing abrasive wear are extremely important methods to protect the mixing chamber. However, the corrosion of metals by high-temperature water vapor should also be considered when preparing for the mixing process.

Section: Testing Methodsmentioning

confidence: 99%

The Effect of Different Dosages of TESPT on Metal Friction and Metal Wear in the Mixing Process

Wang

et al. 2022

Polymers

“…High‐temperature water vapor steam was sprayed during the process of friction and on the rubber compound with a traditional mixing to wet mixing ratio of 1:1.65. Due to its volatility, high‐temperature steam was continuously sprayed to keep the mixing rubber surface moist, which would maintain the accuracy of indoor rubber mixing with the analog mixer 18–23 …”

Section: Methodsmentioning

confidence: 99%

A comparison of the effects of traditional and wet mixing processes of rubber on metal friction and wear

J of Applied Polymer Sci

Zhang

Wang

et al. 2021

Prolonged operations of mixers cause wear of mixer rotors and chamber walls and affect the clearances between the rotors and chamber walls, which reduce the mixing effect, weaken the dispersion of the packing, and affect the quality of rubber products. In this study, the effects of traditional mixing and wet mixing on the friction and wear of the chamber, and the properties of rubber were compared by using 60 phr of a silica natural rubber formulation system. The results show that a silanization reaction occurs between silica and the silane coupling agent during the mixing process and that the reaction rate is fastest when the temperature of the mixing chamber is maintained between 145 and 155°C for 1 min during the mixing process. The products of silanization reaction are ethanol and water; the water vapor that forms at high temperatures corrodes the mixing chamber of the internal mixer and aggravates wear and tear. Due to the high dispersion of silica during wet mixing, the silanization reaction is more complete and water vapor is produced at a high temperature. Hence, the rubber compound obtained by wet mixing has more significant wear on the mixing chamber.

“…During the experiment, the scanning frequency, scanning strain range, and xxx temperature were set to 0.01 Hz, 0.28-40%, and 60 C, respectively. [19][20][21][22][23][24][25][26] The dynamic modulus G 0 curve with strain was obtained. Moreover, the following indicators were calculated during the experiment:…”

Section: Rubber Processing Performancementioning

confidence: 99%

Study on mechanical properties and antifriction of calcium powder filled rubber

Yan

et al. 2021

Polymer Composites

Studies show that long-term operation of the rubber mixer results in wear at the end face of the mixer. End face wear increases the gap between the mixing chamber and the end face, which results in leakage and reduces the mixing performance, thereby affecting the quality of the final product. Therefore, it is of significant importance to investigate the wear of metal face during the mixing process. In the present study, calcium powder was added to the rubber compound using a mechanical blender to obtain a composite material. Then the influence of the calcium powder on metal friction and wear of the end face of the mixer was analyzed. The obtained results show that the calcium powder has anti-friction properties, which can greatly reduce the compound wear on the metal. The lowest corrosion and wear of the compound on the metal was achieved with 5 phr of calcium powder. Meanwhile, it is found that the tensile and tear-resistance properties of the compound with 5 phr of calcium powder are slightly lower than those without calcium powder. However, the compound with 5 phr of calcium powder has higher friction, cold resistance, wet slip resistance, and lower rolling resistance.