“…In turn, carbon forms a refractory titanium carbide and excludes a decrease in the concentration of chromium by chromium carbides formation. It should be noted that the field of chromium-nickel steel applications dominates in the modern rolled metal market [37][38][39][40].…”
This work is devoted to researching the tool electrode behavior and wear under discharge pulses at electrical discharge machining. The experiments were conducted on the workpieces of 12Kh18N10T (AISI 321) chrome-nickel anti-corrosion steel and D16 (AA 2024) duralumin by a 0.25-mm-diameter CuZn35 brass tool in a deionized water medium. The developed diagnostic and monitoring mean based on acoustic emission registered the oscillations accompanying machining at 4–8 kHz. The obtained workpiece and non-profiled tool surfaces were investigated by optical and scanning electron microscopy. Calculated volumetric and mass removal rates showed the difference in the character of wear at roughing and finishing. It was shown that interaction between material components in anti-corrosion steel machining had an explosive character between Zn of brass and Ni of steel at a micron level and formed multiple craters of 30–100 µm. The secondary structure and topology of worn tool surfaces were caused by material sublimation, chemical interaction between material components at high heat (10,000 °C), explosive deposition of the secondary structure. Acoustic diagnostics adequately registered the character of interaction. The observed phenomena at the submicron level and microstructure of the obtained surfaces provide grounding on the nature of material interactions and electrical erosion wear fundamentals.
“…In turn, carbon forms a refractory titanium carbide and excludes a decrease in the concentration of chromium by chromium carbides formation. It should be noted that the field of chromium-nickel steel applications dominates in the modern rolled metal market [37][38][39][40].…”
This work is devoted to researching the tool electrode behavior and wear under discharge pulses at electrical discharge machining. The experiments were conducted on the workpieces of 12Kh18N10T (AISI 321) chrome-nickel anti-corrosion steel and D16 (AA 2024) duralumin by a 0.25-mm-diameter CuZn35 brass tool in a deionized water medium. The developed diagnostic and monitoring mean based on acoustic emission registered the oscillations accompanying machining at 4–8 kHz. The obtained workpiece and non-profiled tool surfaces were investigated by optical and scanning electron microscopy. Calculated volumetric and mass removal rates showed the difference in the character of wear at roughing and finishing. It was shown that interaction between material components in anti-corrosion steel machining had an explosive character between Zn of brass and Ni of steel at a micron level and formed multiple craters of 30–100 µm. The secondary structure and topology of worn tool surfaces were caused by material sublimation, chemical interaction between material components at high heat (10,000 °C), explosive deposition of the secondary structure. Acoustic diagnostics adequately registered the character of interaction. The observed phenomena at the submicron level and microstructure of the obtained surfaces provide grounding on the nature of material interactions and electrical erosion wear fundamentals.
“…The titanium addition hampers chromium carbides' formation and forms refractory carbides of titanium in reaction with carbon. This type of chromium-nickel steel dominates the modern rolled metal market [25][26][27][28]. Duralumin is used mainly in a quenched state and is classified as a durable thermo-hardened construction material for the aerospace industry and unsuitable for welding [29,30].…”
The material removal mechanism, submicrostructure of surface and subsurface layers, nanotransformations occurred in surface and subsurface layers during electrical discharge machining two structural materials such as anti-corrosion X10CrNiTi18-10 (12kH18N10T) steel of austenite class and 2024 (D16) duralumin in a deionized water medium were researched. The machining was conducted using a brass tool of 0.25 mm in diameter. The measured discharge gap is 45–60 µm for X10CrNiTi18-10 (12kH18N10T) steel and 105–120 µm for 2024 (D16) duralumin. Surface roughness parameters are arithmetic mean deviation (Ra) of 4.61 µm, 10-point height (Rz) of 28.73 µm, maximum peak-to-valley height (Rtm) of 29.50 µm, mean spacing between peaks (Sm) of 18.0 µm for steel; Ra of 5.41 µm, Rz of 35.29 µm, Rtm of 43.17 µm, Sm of 30.0 µm for duralumin. The recast layer with adsorbed components of the wire tool electrode and carbides was observed up to the depth of 4–6 µm for steel and 2.5–4 µm for duralumin. The Levenberg–Marquardt algorithm was used to mathematically interpolate the dependence of the interelectrode gap on the electrical resistance of the material. The observed microstructures provide grounding on the nature of electrical wear and nanomodification of the obtained surfaces.
“…The titanium addition hampers chromium carbides' formation and forms refractory carbides of titanium in reaction with carbon. This type of chromium-nickel steel dominates the modern rolled metal market [40][41][42][43]. Duralumin is used mainly in a quenched state and is classified as a durable thermohardened construction material for the aerospace industry and unsuitable for welding [44,45].…”
The mechanism of the material destruction under discharge pulses and material removal mechanism based on the thermochemical nature of the electrical erosion during electrical discharge machining of conductive materials were researched. The experiments were conducted for two structural materials used in the aerospace industry, namely austenite anticorrosion X10CrNiTi18-10 (12kH18N10T) steel and 2024 (D16) duralumin, machined by a brass tool of 0.25 mm in diameter in a deionized water medium. The optimized wire electrical discharge machining factors, measured discharge gaps (recommended offset is 170–175 µm and 195–199 µm, respectively), X-ray photoelectron spectroscopy for both types of materials are reported. Elemental analysis showed the presence of metallic Zn, CuO, iron oxides, chromium oxides, and 58.07% carbides (precipitation and normal atmospheric contamination) for steel and the presence of metallic Zn, CuO, ZnO, aluminum oxide, and 40.37% carbides (contamination) for duralumin. For the first time, calculating the thermochemistry parameters for reactions of Zn(OH)2, ZnO, and NiO formation was produced. The ability of Ni of chrome–nickel steel to interact with Zn of brass electrode was thermochemically proved. The standard enthalpy of the Ni5Zn21 intermetallic compound formation (erosion dust) ΔH0298 is −225.96 kJ/mol; the entropy of the crystalline phase Scint is 424.64 J/(mol·K).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.