Comparing Cable Discharge Events to IEC 61000-4-2 or ISO 10605 Discharges

Arndt, Bastian; Nieden, Friedrich zur; Pohmerer, Rainer; Edenhofer, Johannes; Frei, Stephan

doi:10.1109/emczur.2009.4783414

Cited by 12 publications

(4 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As shown in Table 2, when the charging voltage reaches 1.5 KV, in spite of capacitor protection, the pin voltage spike of the device will exceed the pressure limit 40 V, which conforms to the calculation in Bastian Arndt's paper of "Comparing Cable Discharge Events to IEC 61000-4-2 or ISO 10605 Discharges". 1.5 kV should be recommended as the risk voltage of cable charging voltage [6]. The pulse width of the cable discharge is calculated as follows [7]:…”

Section: Simulation Verificationmentioning

confidence: 99%

Design and Verification of Equivalent Circuit for Cable Electrostatic Discharge

Lu¹,

Ji²,

Song³

et al. 2016

JAMP

View full text Add to dashboard Cite

In the process of production, transportation and assembly, cable assemblies can get a lot of electrostatic charge by friction, dragging, pulling and induction. These residual charges can be discharged when Electrostatic sensitive device connected with it and can cause the complete failure or potential failure of the electrostatic sensitive product. In this paper, the theoretical model of cable assemblies is established by analyzing the characteristics of cable assemblies, and the equivalent RF circuit is designed. The static discharge characteristics of the cable are analyzed and verified by simulation.

show abstract

Section: Simulation Verificationmentioning

confidence: 99%

Design and Verification of Equivalent Circuit for Cable Electrostatic Discharge

Lu¹,

Ji²,

Song³

et al. 2016

JAMP

View full text Add to dashboard Cite

show abstract

“…Through close cooperation, these organizations have emitted documents in the form of standards, regulations and manuals of good practice [15]. Thus, the electromagnetic compatibility standards for ESD immunity testing are applied [15]: [20].…”

Section: Regulations Concerning Esd Testingmentioning

confidence: 99%

“…An overview of the concepts that led to the international regulations implementation is described in paper [14], and a comparative analysis on the standard methodology is done in paper [15].…”

Section: Introductionmentioning

confidence: 99%

Testing equipment to electrostatic discharge. Case study-communication cables

Moasa

Helerea

2012

2012 International Conference on Applied and Theoretical Electricity (ICATE)

View full text Add to dashboard Cite

The paper deals with the analysis of the characteristics of electrostatic discharges (ESD) processes and the impact of ESD to the performances of equipment, especially to the communication cables. ESD current models are analyzed, and, in conformity with basic standards in this field the measuring methods of the discharges are applied. The comparative results for unshielded and shielded cables are done. The experimental determinations show that the cable shielding offers an improvement to their functionality, but it does not totally eliminate the probability to damage on the electrostatic discharge actions. New mitigation techniques should be developed.

show abstract

“…ESD measurement & simulation set up1) Charged Cable Model (CCM) 정전기 방전(ESD)에 의한 전자제어장치의 손상Transactions of the Korean Society of AutomotiveEngineers, Vol. 21, No.…”

mentioning

confidence: 99%

Charged Cable Model (CCM) ESD Damage to ECU

Ha¹,

Jung²

2013

Transactions of the Korean Society of Automotive Engineers

View full text Add to dashboard Cite

: ESD damage by Charged Cable Model (CCM) is introduced. Due to its own impedance characteristic unlike Human Body Model (HBM) or Machine Model (MM) electric component can be destroyed even though it is located after typical protection circuit. Possible mechanism of ESD damage to automotive electric control unit (ECU) in vehicle environment by CCM discharge was investigated. Based on investigation, field-returned vehicle whose ECU is expected to be damaged by CCM discharge was tested to reproduce it and similar electric component destruction inside ECU was observed. Suggestions to reduce the possibility of ESD damage by CCM are introduced.

show abstract

Comparing Cable Discharge Events to IEC 61000-4-2 or ISO 10605 Discharges

Cited by 12 publications

References 1 publication

Design and Verification of Equivalent Circuit for Cable Electrostatic Discharge

Design and Verification of Equivalent Circuit for Cable Electrostatic Discharge

Testing equipment to electrostatic discharge. Case study-communication cables

Charged Cable Model (CCM) ESD Damage to ECU

Contact Info

Product

Resources

About