Calculations of the frictional heating of a locomotive wheel attending rolling plus sliding

Gupta, Vikas; Hahn, G. T.; Bastias, P.C.; Rubin, Carol

doi:10.1016/0043-1648(95)06691-8

Cited by 26 publications

(14 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The boundary value --initial value problem stated above can be solved numerically as shown by Gupta et al [6,7]. The aim of the elaboration presented here, however, is to obtain an analytic solution and to derive simple engineering formulae for the surface temperature from this solution.…”

Section: Problem Solutionmentioning

confidence: 99%

The Surface Temperature of a Halfplane Heated by Friction and Cooled by Convection

Fischer

Werner

Knothe

2001

Z. angew. Math. Mech.

View full text Add to dashboard Cite

Based on earlier works by the authors an analytical expression for the surface temperature of a halfplane heated by fast moving rolling/sliding contact and cooled by convection on the surface of the halfplane is presented by applying the Laplace transformation technique and the solution of a Volterra integral equation of the second kind. Furthermore, the influence of heat conduction in the rolling/sliding direction is investigated.

show abstract

Section: Problem Solutionmentioning

confidence: 99%

The Surface Temperature of a Halfplane Heated by Friction and Cooled by Convection

Fischer

Werner

Knothe

2001

Z. angew. Math. Mech.

View full text Add to dashboard Cite

show abstract

“…Moreover, the yield strength of material would be decreased in this case. After a certain number of continuous loading, the temperature may exceed 700ºC [21], and cracks can be initiated within the white etching layer due to its brittle behaviour when a traction is present [6].…”

Section: Temperature Distribution On Railmentioning

confidence: 99%

A tool to estimate the wheel/rail contact and temperature rising under dry, wet and oily conditions

Vo¹,

Zhu²,

Kosasih³

2014

WIT Transactions on the Built Environment

View full text Add to dashboard Cite

In this paper, finite element method (FEM) has been applied to evaluate the wheel/rail contact stress under different contact conditions. The elastic-plastic model coded in ANSYS/LS-DYNA includes a whole wheel, 680 mm of the canted rail, and sub-components of the track (railpads, sleepers, and ballast). The three values of friction coefficient 0.4, 0.2 and 0.07 have been chosen to model the dry, wet and oily environmental contacts, respectively. The high mechanical stresses exerted at the contact area will cause the temperature rise, which results in decreasing of the yield strength of the wheel/rail. The growth of temperature is a major source of the various microstructure changes that occurs on the rail surface, especially the formation of White Etching Layer (WEL). Therefore, a theoretical calculation of heat generation has also been implemented in the current research. The output data from the FEM models have been considered as the input for the theoretical thermal model to examine temperature rising on and beneath the rail surface. The combination of finite element method for contact stress and theoretical thermal method for temperature variation would provide a better understanding about wheel/rail contact under a variety of contact conditions (dry, wet, and oily). Various scenarios of damage mechanisms of rail have been considered in the paper.The obtained results from the model have revealed that the influence of environmental conditions on normal contact stress, pressure and contact area is negligible. In contrast, the magnitude of the Von-Mises stress and lateral and longitudinal stresses components can be significantly varied depending on the friction conditions. Moreover, the environmental condition has shown a major effect on the temperature rising at the contact zone.

show abstract

“…Among them, the most recent and pertinent works are: Savkoor and Ouwerkerk [45], Gupta et al [46], Kuhn and Balan [47], Scherge et al [48], Shakhvorostov et al [49], Larbi et al [50], Li et al [51], Abdel-Aal [52][53][54], Maeda et al [55], Colaco et al [56], and Nurnberg et al [57]. The foregoing review of literatures on the state of the art pertaining to the energy approach to wear processes reveals that the frictional energy dissipation is a promising feature of tribosystems to characterize wear process.…”

Section: Sliding Contactmentioning

confidence: 99%

On the Thermodynamics of Friction and Wear―A Review

Amiri

Khonsari

2010

Entropy

165

View full text Add to dashboard Cite

show abstract

Calculations of the frictional heating of a locomotive wheel attending rolling plus sliding

Cited by 26 publications

References 10 publications

The Surface Temperature of a Halfplane Heated by Friction and Cooled by Convection

The Surface Temperature of a Halfplane Heated by Friction and Cooled by Convection

A tool to estimate the wheel/rail contact and temperature rising under dry, wet and oily conditions

On the Thermodynamics of Friction and Wear―A Review

Contact Info

Product

Resources

About