Bellman Ford algorithm - in Routing Information Protocol (RIP)

Sulaiman, Oris Krianto; Husein, Amir Mahmud; Nasution, Khairuddin; Haramaini, Tasliyah

doi:10.1088/1742-6596/1007/1/012009

Cited by 17 publications

(12 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The Analysis Hierarchy Process can synthesize the assessments into a comprehensive estimate with the relative priorities of various action alternatives. [15], [16] The priority generated by the Analysis Hierarchy Process is the basic unit used in all types of analysis and stimulates the emergence of ideas for carrying out creative actions and for evaluating the effectiveness of those actions. In addition, the Analysis Hierarchy Process can also track inconsistencies in the considerations and preferences of participants/respondents.…”

Section: Analysis Hierarhcy Process (Ahp)mentioning

confidence: 99%

Application of Taguchi and Analysis Hierarcy Process Methods for Furan Design on Metal Casting Industry

Hasibuan¹,

Parinduri²,

Sulaiman³

et al. 2018

IJET

View full text Add to dashboard Cite

In the preparation of furan the raw material used are, Silica Sand, Resin, and Catalyst. Some problem that occurs are high level of water, high level of sour, high level of clay, unsuitable distribution, and low permeability. All those problems above make the power of furan not suitable with the target that has been stated, so that furan can easily be broken, cracked, and do not stand with high temperature and its power becomes weak. The result of this research is that the optimal combination based on the highest TOPSIS score is A1 B2 C3 with the composition of Resin 1.3%, Catalyst 22.5% and new sand 15% + reclaim sand 85%. The coefficient of loss function compression strength is 4.611,11 and 10.375 for the shear strength. The raising quality based on the confirmation experiment is 0.1018 for the compression strength and 0.2339 for the shear strength. The value of S/N in the confirmation experiment for the compression strength is 20.5817 and 23.0480, in which both numbers are in the trust interval limitation that has been decided. It shows that TOPSIS procedure is able to increase furan quality for both responses, that is compression strength response, and shear strength response all at once in one parameter setting.

show abstract

Section: Analysis Hierarhcy Process (Ahp)mentioning

confidence: 99%

Application of Taguchi and Analysis Hierarcy Process Methods for Furan Design on Metal Casting Industry

Hasibuan¹,

Parinduri²,

Sulaiman³

et al. 2018

IJET

View full text Add to dashboard Cite

show abstract

“…In order to overcome the causes of lower productivity as above, it is highly required solution with improvements as in generally called machine-ability up. In order to improve machine-ability of carbon steel as material many used by SMIs in Medan, several researchers reported already the methods to improve a machineable of the material [1], [2]. Wassila's publication reported that parameters of cutting such as speed of cutting (V), feed (f), and depth of cutting (a) can be more optimum to shorten time duration (production) and to have maximum productivity.…”

Section: Introductionmentioning

confidence: 99%

Study of Optimum Cutting While Lathing Carbonate Steel VCN-150 Uses a Layered Carbide Chisel PVD on Dry and Wet Condition

Harahap¹,

Bakhori²,

Napid³

et al. 2018

IJET

View full text Add to dashboard Cite

To improve the productivity of this machining perhaps it may be recommended in a dry cutting but a dry cutting is recognized very sensitive to a high temperature. In this case, in order to overcome is perhaps required by using a tool carbide either in layers or without any layers whereby each layer has certain superior. There was conducted an experiment to have an optimum cutting on a carbon steel VCN-150 using a layers tool carbide and Respond Surface Method (RSM) with a CCD operation. The result of study recommended that condition optimum cutting shall be achieved (When cutting tc ) on a medium machining refers to ISO 3685 and medium surface roughness (Ra ) ISO 1320. Statistically, there is no found significant difference between a dry and wet cutting on optimum dry condition.

show abstract

“…This causes an increase in the number of power plants and the resulting capacity in the transmission line connecting the power station to the load centers will increase. Power systems are widely interconnected, need an interconnection system because in addition to transmission from the transmission line there is a power plant where energy composition by type of power plant: (PLTGU, PLTU, PLTG, PLTD and PLTP) and load centers to minimize total power capacity and cost [11], [12]. The interconnection transmission allows taking advantage of the diversity of loads, the availability of sources and prices for power supplies to the load at minimum cost with the required reliability.…”

Section: Introductionmentioning

confidence: 99%

Analysis of Stability Improvements by Using Capacitors

Yusmartato¹,

Pelawi²,

Ramayulis³

et al. 2018

IJET

View full text Add to dashboard Cite

The demand for electricity has increased substantially while the expansion of electricity generation, power transmission is very limited, due to environmental restrictions, consequently some transmission lines, limiting power factor. Power flow in the generation system, covering the area of North Sumatra and Aceh which is managed by PT. PLN (Persero), ETAP 4.0 (Electrical Transient Analizer Program) is a program that can display GUI (Graphical User Interface) with unlimited bus number, ETAP 4.0 is useful for Power flow study. The data required by ETAP 4.0 on a generation system is a one-line diagram, nominal kV, and generator, bus, transformer, transmission, and safety rating. The power flow approach method used is the Newton-Raphson method with maximum iteration of 99 and the accuracy of 0.000001. The problem of power flows under consideration is the normal state system, one transmission is disconnected, one of the plants is not operating. The results of the power flow study for each problem obtained the lowest bus voltage, the highest losses in the transmis. The largest power distributed in power plants, new in high voltage transmission, increases the power of power from power to load, changes in voltage problems and improves system stability. This paper aims to verify the capacitor's ability to improve voltage regulation (voltage stability) in electric power transmission systems, from this capacitor simulated using ETAP 4.0 included in Newton-Raphson model.

show abstract

Bellman Ford algorithm - in Routing Information Protocol (RIP)

Cited by 17 publications

References 1 publication

Application of Taguchi and Analysis Hierarcy Process Methods for Furan Design on Metal Casting Industry

Application of Taguchi and Analysis Hierarcy Process Methods for Furan Design on Metal Casting Industry

Study of Optimum Cutting While Lathing Carbonate Steel VCN-150 Uses a Layered Carbide Chisel PVD on Dry and Wet Condition

Analysis of Stability Improvements by Using Capacitors

Contact Info

Product

Resources

About