A high gain ultra-wideband monopole antenna

De, Srija; Sarkar, Partha Pratim

doi:10.1016/j.aeue.2015.04.012

Cited by 21 publications

(15 citation statements)

References 5 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A thorough observation of the antenna structure shows that the gap ( h of Figure A) maintained in between circular radiating disk and the partial ground plane plays a very important role in optimum design . If the gap is too small, additional interference deteriorates the performance of the antenna.…”

Section: Parametric Optimizationmentioning

confidence: 99%

“…A thorough observation of the antenna structure shows that the gap (h of Figure 1A) maintained in between circular radiating disk and the partial ground plane plays a very important role in optimum design. 31 If the gap is too small, additional interference deteriorates the performance of the antenna. On the other hand, a large separation between the radiator and the patch means that the available ground plane is too narrow to act as an effective ground for the antenna.…”

Section: Parametric Optimizationmentioning

confidence: 99%

See 1 more Smart Citation

Bandwidth enhancement of monopole antenna using stubbed ground plane

Kerketta

Ghosh

2019

Int J RF Microw Comput Aided Eng

View full text Add to dashboard Cite

This article demonstrates a method of enhancing the bandwidth of a planar monopole antenna with minor modifications of the ground plane suitable for medical applications. The narrowband monopole antenna is mounted on a modified ground plane, thus extending its impedance bandwidth and increasing the gain. The partial ground plane is transformed by integrating a rectangular plate on the upper edge of the ground plane, thus achieving a bandwidth ratio of 12:1 from 3 GHz to 37.26 GHz and again from 42.5 GHz onwards.

show abstract

Section: Parametric Optimizationmentioning

confidence: 99%

Section: Parametric Optimizationmentioning

confidence: 99%

Bandwidth enhancement of monopole antenna using stubbed ground plane

Kerketta

Ghosh

2019

Int J RF Microw Comput Aided Eng

View full text Add to dashboard Cite

show abstract

“…The slot between radiators of MIMO antenna produces more than 20 dB of isolation and is used for RADAR application . The UWB monopole antenna with proper structure planning results in high gain . The half slot structure creates multiband operation and enhances isolation .…”

Section: Introductionmentioning

confidence: 99%

Four‐port shared rectangular radiator with defected ground for wireless application

Chouhan

Malviya²

2020

Int J Communication

View full text Add to dashboard Cite

In this research work, a modified shared rectangular radiator is proposed for 5.7-GHz wireless application using multiple cuts and partially stepped ground. The shared design requires no isolating structure to decouple the ports. The proposed shared geometry produces >13 dB isolation in the 4.4-to 6.4-GHz operating band. The gain varies from 3.0 to 6.2 dBi, and radiation efficiency is >70 % in the band. The mutual coupling among the port is reduced by orthogonal arrangement of ports, and envelope correlation coefficient (ECC) is <0.04 in the presented band. Apart from this, isolation in the proposed shared radiator is enhanced by additional multiple cuts with stepped ground. The indooroutdoor suitability of multiple input multiple output (MIMO) antenna for isotropic and Gaussian medium is checked by mean effective gain (MEG) and specific absorption rate (SAR). The presented results of MEG and SAR fulfill the required safety norms as per the ITU for different environments. K E Y W O R D SECC, MEG, MIMO antenna, isolation, SAR, TARC

show abstract

“…In the present communication era, wireless communication is playing a vital role in the human being's life . Keeping this under consideration, firstly, Federal Communication Commission's (FCC) had approved the protocols for the commercial use of ultra‐wide band (UWB) in February 2002 . In the April month of same year, the FCC had given formal approval for the unlicensed use of technology with frequency ranging from 3.1 to 10.6 GHz .…”

Section: Introductionmentioning

confidence: 99%

Design of printed monopole antenna with band notch characteristics for ultra‐wideband applications

Sharma

Bhatia

2019

Int J RF Microw Comput Aided Eng

View full text Add to dashboard Cite

A novel design of printed monopole antenna for the ultra‐wideband (UWB) applications with band notch characteristics at wireless local area network (WLAN) and X‐band satellite communication system has been proposed in this manuscript. Two different types of feed lines, that is, simple and tapered are used to excite the proposed antenna. Initially, designed antenna is excited by using simple 50 Ω transmission line after that tapered transmission line is introduced to enhance the impedance matching throughout the UWB frequency range (3.1‐10.6 GHz). A comparison of designed antenna with simple and tapered feed line on the basis of impedance matching has also been made in this article, and found that later case reports better impedance matching in terms of Voltage Standing Wave Ratio (VSWR) bandwidth (2.45‐12.0 GHz). Further, the notch bands are embodied into the designed antenna by using two split ring slots and one horizontal slot. The antenna with outer ring slot rejects the WLAN frequency band and antenna with inner ring junks the X‐band satellite communication signal. The notch frequency has been adjusted by optimizing the dimensions of split ring slots as well as horizontal slot, which are incised on the structure of proposed antenna. By adjusting all the parameters of the etched slots of proposed antenna, dual band notched characteristics centered at frequencies 5.4 and 7.4 GHz has been achieved. Designed antenna is also compact (30 × 30 mm2) and capable to suppress the interference of WLAN and X‐band satellite communication signal from the entire range of UWB passband. The proposed antenna is designed on low cost FR4 glass epoxy substrate with 1.6 mm thickness and dielectric constant 4.4. Antenna is designed and simulated by using HFSS V13 simulator and further, it is fabricated and tested for the validation of results. Simulated and measured results are also juxtaposed and found in good agreement with each other.

show abstract

A high gain ultra-wideband monopole antenna

Cited by 21 publications

References 5 publications

Bandwidth enhancement of monopole antenna using stubbed ground plane

Bandwidth enhancement of monopole antenna using stubbed ground plane

Four‐port shared rectangular radiator with defected ground for wireless application

Design of printed monopole antenna with band notch characteristics for ultra‐wideband applications

Contact Info

Product

Resources

About