На основі складених аналітичних залежностей було змодельовано у середовищі САПР «MSC.Adams» процес конічного зношування алмазної втулки. Аналіз результатів комп'ютерного моделювання дозволив встановити емпіричний зв'язок між величиною конічного зношування втулки та параметрами процесу різання. Результатом досліджень є практичні рекомендації щодо покращення конструкції алмазної втулки Ключові слова: конус, алмазна втулка, зношування, моделювання, силові характеристики, MSC.Adams На основании составленных аналитических зависимостей было смоделировано в среде САПР «MSC.Adams» процесс конического износа алмазной втулки. Анализ результатов компьютерного моделирования позволил определить эмпирическую связь между величиной конического износа втулки и параметрами процесса резания. Результатом исследования являются практические рекомендации по улучшению конструкции алмазной втулки Ключевые слова: конус, алмазная втулка, износ, моделирование, силовые характеристики, MSC.Adams
Під час відокремлення монолітів від масиву алмазно-канатними установками зберігається його цілісність, але разом з цим виникають супутні проблеми та питання, такі як вибір оптимальних розмірів моноліту і кута буріння для заведення канату, або які механізми чи пристосування використовувати при відділенні моноліту від масиву. Процес відокремлення моноліту від масиву алмазними канатними установками здебільшого супроводжується виникненням кількісних втрат каменю, на які впливають такі параметри: кількість площин оголення моноліту, розміри моноліту, який вилучається, абсолютний діаметр буру, товщина алмазного канату. Якісні втрати під час використання алмазно-канатних пил майже відсутні. Однак на їх виникнення впливають такі чинники: відхилення канату від заданої площини пропилу, нерівномірне зношування алмазних втулок і зміна товщини алмазного шару в результаті його зношування під час різання.
Головним завданням, яке вирішується під час написання цієї статті, є встановлення дослідним шляхом залежності значення величини адгезії від типу профілю композитних стержнів за умови їх застосування для армування виробів з каменю. В межах роботи розглянуто доцільність застосування композитної арматури з вдавленим, спірально наклеєним (під кутом 35° та 80°) і покритим піщаною сумішшю профілів та їх здатністю до формування взаємодії з епоксидними в’яжучими сумішами. За результатами виконання досліду було встановлено здатність кожного з типів досліджуваних профілів чинити опір вириванню з кам’яного зразка (при цьому як еталон, відносно якого порівнювалися всі інші зразки, було застосовано сталевий стержень з періодичним профілем). За результатами зіставлення одержаних результатів для армування конструкцій, що експлуатуватимуться під дією згинальних або розривних навантажень, в тому числі і для складних виробів, з’єднання яких передбачено шляхом застосування посилюючих стержнів, найкращим варіантом з-поміж порівнюваних будуть стержні, поверхня яких покрита піщаною сумішшю.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.