Abstract:Plasma-wall interaction (PWI) is important for the material choice in ITER and for the plasma scenarios compatible with material constraints. In this paper different aspects of the PWI are assessed in their importance for the initial wall materials choice: CFC for the strikepoint tiles, W in the divertor and baffle and Be on the first wall. Further material options are addressed for comparison, such as W divertor / Be first wall and all-W or all-C.One main parameter in this evaluation is the particle flux to the main vessel wall. One detailed plasma scenario exists for a Q=10 ITER discharge [ 1 ] which was taken as the basis of further erosion and tritium retention evaluations. As the assessment of steady state wall fluxes from a scaling of present fusion devices indicates that global wall fluxes may be a factor of 4±3 higher, this margin has been adopted as uncertainty of the scaling.With these wall and divertor fluxes, important PWI processes such as erosion and tritium accumulation have been evaluated:• It was found that the steady state erosion is no problem for the lifetime of plasma-facing divertor components. Be wall erosion may pose a problem in case of a concentration of the wall fluxes to small wall areas. ELM erosion may drastically limit the PFC lifetime if ELMs are not mitigated to energies below 0.5 MJ.• Dust generation is still a process which requires more attention. Conversion from gross or net erosion to dust and the assessment of dust on hot surfaces need to be investigated.• For low-Z materials the build-up of the tritium inventory is dominated by co-deposition with eroded wall atoms.• For W, where erosion and tritium co-deposition are small, the implantation, diffusion and bulk trapping constitute the dominant retention processes. First extrapolations with models based on laboratory data show small contributions to the inventory. For later ITER phases and the extrapolation to DEMO additional tritium trapping sites due to neutron-irradiation damage need to be taken into account.Finally the expected values for erosion and tritium retention are compared to the ITER administrative limits for the lifetime, dust and tritium inventory.

No abstract

Abstract:Interactions between the plasma and the vessel walls constitute a major engineering problem for next step fusion devices, such as ITER, determining the choice of the plasma-facing materials. A prominent issue in this choice is the tritium inventory build-up in the vessel, which must be limited for safety reasons. The initial material selection, i.e. beryllium (Be) on the main vessel walls, tungsten (W) on the divertor upper baffle and dome, and carbon fibre composite (CFC) around the strike points on the divertor plates, results both from the attempt to reduce the tritium inventory and to optimise the lifetime of the plasma facing components (PFCs).In the framework of the EU Task Force on Plasma-Wall Interaction (PWI TF), the many physics aspects governing the tritium inventory are brought together. Together with supporting information from international experts represented by the ITPA SOL/DIV section, this paper describes the present status of knowledge of the in-vessel tritium inventory build-up. Firstly, the main results from present fusion devices in this field are briefly reviewed. Then, the processes involved are discussed: implantation, trapping and diffusion in plasma facing materials are considered as well as surface erosion and co-deposition of tritium with eroded material. The intermixing of the different materials and its influence on hydrogen retention and co-deposition is a major source of uncertainty on present estimates and is also addressed.Based on the previous considerations, estimates for the tritium inventory build up are given for the initial choice of ITER materials, as well as for alternative options. Present estimates indicate a build-up of the tritium inventory to the administrative limit within a few hundred nominal full power D:T discharges, co-deposition with carbon being the dominant process. Therefore, tritium removal methods are also an active area of research within the EU PWI TF, and are discussed. An integrated operational scheme to slow the rate of tritium accumulation is presented, which includes plasma operation as well as conditioning procedures. † Current address: Fusion for Energy,

The ion-driven retention of deuterium in polycrystalline tungsten (PCW) is studied experimentally and theoretically as a function of temperature, incident ion energy and ion fluence.

Surface and sub-surface morphology and deuterium retention in polycrystalline tungsten, undamaged and pre-damaged with 5. The dependence of the D retention on the damage level and the implanted fluence was studied, and the results show saturation for 0.4 dpa independent of the deuterium implantation fluence. Additionally, it was observed that self-implantation introduces high temperature traps which can almost completely be removed by annealing at 1200 K.

No abstract

No abstract

No abstract