Boriding abilities of boriding media based on boron carbide, amorphous boron and mixtures for a simultaneous saturation by boron, chromium and titanium have been compared. As an object of study boride coatings on carbon steels 45 and U8A have been chosen. Borating was done from powder mixtures in a chamber furnace of SNOL type. The microstructure and thickness of the diffusion coatings were studied on cross microsections by means of optical microscopy. The boride phases were identified by «color etching» and by X-ray diffraction. It is shown that during simultaneous saturation of carbon steels with boron, chromium and titanium the diffusion processes occur much more intensively. Addition of carbide-forming elements such as chromium and titanium into a boriding mixture results in a significant acceleration of boron diffusion in carbon steels 45 and U8A. During a simultaneous multicomponent saturation with boron, titanium and chromium the rate of diffusion layer formation on carbon steels is higher than under one-component boriding. In the case of a multicomponent saturation by boron along with strong carbide-forming elements (chromium and titanium), an increase of the carbon content of carbon steel under saturation from 0.45 to 0.8 wt.% has little effect on the formation of a diffusion layer. While in the case of one-component boriding the carbon content of the steel significantly affects both the thickness and microstructure of a boride coating, during a simultaneous saturation with boron, titanium and chromium the carbon content of the steel has practically no effect on the diffusion coating thickness. Проведено сравнение борирующей способности насыщающих сред для борирования на основе карбида бора и аморфного бора, а также смеси для одновременного насыщения бором, хромом и титаном. В качестве объекта из-учения были выбраны боридные покрытия на углеродистых сталях 45 и У8А. Борирование производили из порош-ковых смесей в камерной печи типа СНОЛ. Исследование микроструктуры и толщины диффузионных покрытий производили на поперечных микрошлифах при помощи оптической микроскопии. Идентификацию боридных фаз производили методом "цветного травления" и при помощи рентгеновской дифрактометрии. Показано, что при од-новременном насыщении бором, хромом и титаном углеродистых сталей, диффузионные процессы протекают значительно интенсивнее. Введение в состав борирующей смеси карбидообразующих элементов -хрома и тита-на способствует значительному ускорению процессов диффузии бора в углеродистых сталях 45 и У8А. При одно-временном многокомпонентном насыщении бором, хромом и титаном скорость образования диффузионного слоя на углеродистых сталях выше, чем при борировании. В случае многокомпонентного насыщения бором совместно с сильными карбидообразующими элементами (хром и титан) увеличение содержания углерода в насыщаемой уг-леродистой стали от 0,45 до 0,8 мас.% оказывает слабое влияние на процесс образования диффузионного слоя. Если при однокомпонентном борировании содержание углерода в стали значительно влияет как на толщину,...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.