1Самарский государственный аэрокосмический университет имени академика С.П. Королёва (национальный исследовательский университет) 2 ОАО «Металлист-Самара» В статье рассматриваются основные источники тепла, поступающего в опору авиационного двига-теля, исследуются способы их определения и даётся их количественное сравнение для определенных условий работы опоры компрессора. На основании определения количества тепла, поступающего от ка-ждого из источников, а также по результатам предварительно выполненного термогазодинамического расчета, выполняются последовательно гидравлический расчёт воздушного охлаждения опоры и вычис-ляется распределение коэффициентов конвективной теплоотдачи и температуры по стенкам опоры дви-гателя. Затем по полученным данным производится структурный тепловой расчёт. В результате струк-турного расчёта определяется распределение температуры в элементах опоры. Приводятся примеры оценки влияния количества тепла, выделяемого различными источниками, а также влияния изменения количества тепла от отдельного источника на уровень потребной прокачки масла через двигатель, при определённой схеме охлаждения опоры. Сравнивается интенсивность теплоотдачи по источникам в за-висимости от режима работы двигателя. На основании предложенной последовательности расчётов была составлена методика определения теплового состояния опоры авиационного двигателя, которая позволит выбирать требуемую систему охлаждения, а также оценить и скорректировать основные параметры мас-ляной системы двигателя.Масляная система, тепловой поток, температура, коэффициент теплоотдачи, трение, уплот-нение, подшипник, эффективность, охлаждение, методика.
Metallist-Samara JSC has developed a fundamentally new design of a unified double-circuit burner of a low-emission combustion chamber (LECC) of a ground-based gas turbine unit (GTU), adapted for manufacturing with the help of an innovative technology by selective laser melting (SLM) of metal powders using CAD models. Several batches of burners were made and control studies were carried out characterizing the quality of manufacturing according to the established procedure. Deficiencies inherent in the SLM process were discovered, the main of which are: raised roughness, in particular, of the fuel channels of the main and duty zones; microporosity, microalloying; microcracks; instability of flow characteristics; local non-sintering zones of the layers grown on the burner body. As a result of the analysis of the state of the manufactured burners, research and refinements, it was found that most of the identified shortcomings can be eliminated during further development of the modes and parameters of the technological process. Currently, difficult engineering problems associated with the implementation of additive manufacturing technologies have been overcome.
The paper deals with the questions of introducing the additive technology of selective laser melting (SLM) into the production of the main structural elements of a combustion chamber for ground-based gas pumping, power and transport gas turbines. A fundamentally new design of a low-emission two-circuit burner was developed, adapted for the manufacture of products with a complex geometry through the use of selective laser melting (SLM) of metal powders according to mathematical CAD-models with the help of an advanced production technology. Technical difficulties associated with the implementation of additive manufacturing technology were overcome. The process chain was tried out from design to manufacturing and quality control of finished structural elements under conditions of mass production. The deficiencies of the parts manufactured by the additive technology were revealed and ultimately eliminated. Successful development of burners for a low-emission combustion chamber using a new technology significantly reduces labor intensity and time of production while maintaining high quality.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.