Методом первоначальных деформаций изучено влияние толщины упрочнённо-го слоя на распределение остаточных напряжений в области концентратора. Установлено, что толщина деформированного слоя оказывает существенное влияние на распределение остаточных напряжений в концентраторе.Ключевые слова: остаточные напряжения, первоначальные деформации, по-верхностное упрочнение, плоская деталь с концентратором.
Residual stresses in the dangerous section of toothed wheels made of materials and according to practices accepted in aviation engine construction have been determined using a mechanical method. The influence of the technology of manufacturing of toothed wheels, thermo-chemical treatment, hardening and coating on the residual stresses has been examined. Current technologies of manufacturing toothed wheels lead to significant dispersion of residual stresses, especially after thermo-chemical treatment. Therefore, the results have been statistically processed for each batch of parts and the average values are shown on the residual stress diagrams. We demonstrate the possibility of determining residual stress distribution in the dangerous section of a wheel tooth by the initial deformations of the reference specimen, which makes it possible to keep the part under examination unimpaired. A plate made of the same material as the toothed wheel and hardened simultaneously with the part under examination was used as a reference specimen. The influence of residual stresses on the fatigue resistance of toothed wheels by the average integral residual stresses criterion that takes into account both the value of residual stresses and the nature of their distribution in the dangerous section of toothed wheels was examined.
Самарский государственный аэрокосмический университет имени академика С.П. Королёва (национальный исследовательский университет)Изучена возможность использования образцов-свидетелей, обрабатываемых одновременно с дета-лями, для оценки влияния гидродробеструйной обработки на предел выносливости деталей с концентра-торами напряжений на примере цилиндрических образцов с отверстием из стали 40Х с круговым надре-зом полукруглого профиля радиуса 0,3 мм. Исследование показало, что расхождение между расчётными и экспериментальными значениями остаточных напряжений в гладких образцах не превышает 8%, в об-разцах с надрезом -6%. При оценке влияния гидродробеструйной обработки на предел выносливости при изгибе в случае симметричного цикла полых цилиндрических образцов из стали 40Х с надрезом ра-диуса 0,3 мм установлено, что использование рассчитанного по первоначальным деформациям образца-свидетеля распределения остаточных напряжений позволяет прогнозировать приращение предела вы-носливости образцов в условиях концентрации напряжений с точностью до 8%. Показано, что при про-гнозировании приращения предела выносливости упрочнённых гидродробеструйной обработкой образ-цов из стали 40Х с концентраторами напряжений целесообразно использовать критерий среднеинте-гральных остаточных напряжений, вычисленный по толщине поверхностного слоя опасного сечения, равной критической глубине нераспространяющейся трещины усталости.Поверхностное упрочнение, образец-свидетель, остаточные напряжения, предел выносливости.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.