1 Сибирский государственный индустриальный университет 2 Уральский федеральный университет им. первого Президента России Б.Н. Ельцина (г. Екатеринбург) РАСЧЕТ ПРОИЗВОДИТЕЛЬНОСТИ ДРОБИЛКИ С ПОСТУПАТЕЛЬНЫМ ДВИЖЕНИЕМ ЩЕКИ * Аннотация. Представлена дробилка с поступательным движением щеки, имеющая большую производительность по сравнению с существу-ющими конструкциями. Предложена формула расчета ее минимальной производительности, из анализа которой видно, что при заданной степени дробления (отношении размера дробимого куска к величине разгрузочной щели) производительность щековой дробилки увели-чивается с увеличением хода сжатия и угла захвата.Ключевые слова: дробилка с поступательным движением щеки, производительность, угол захвата. CALCULATION OF PERFORMANCE CRUSHER WITH TRANSLATION MOVEMENT OF JAWAbstract. Presented is the grinder with translation movement of jaw, which demonstrates better performance in comparison to existing designs. Presented is formula of its minimum speed calculation, analysis of which shows that for given degree of fragmentation (the ratio of size of crushed piece to value discharge hole) jaw crusher performance increases with the increase of compression stroke and angle of capture.Keywords: grinder with translation movement of jaw, performance, angle of capture.Расход энергии на дробление различных материалов составляет большую (до 5 %) долю в энергетическом балансе мира [1]. Для измельчения кусков многие про-мышленные (металлургические, горные и др.) произ-водства применяют дробилки, в том числе и щековые.Одним из основных показателей работы дробилок является их производительность, т.е. отношение пере-работанного количества (массы или объема) материала к единице времени.Большое влияние на производительность щековых дробилок любого типа имеет траектория движения под-вижной щеки. В дробилках с простым движением щеки малый ход сжатия в верхней части камеры дробления приводит к ненадежному захвату и неравномерности процесса дробления по высоте рабочего пространст-ва. Верхняя часть камеры дробления не обеспечивает достаточным количеством материала нижнюю часть с увеличенным ходом щеки, что приводит к значительно-му снижению общей производительности.В дробилках со сложным движением щеки траек-тория движения точек последней в нижней части на отдельных этапах ее движения значительно препятст-вует разгрузке материала, что также снижает произво-дительность.Для устранения указанных недостатков в Сибирс-ком государственном индустриальном университете разработана конструкция дробилки с поступательным движением щеки [2]. Ее сущность заключается в том, что подвижная щека верхним и нижним концами кре-пится к приводным кривошипным валам, эксцентриси-тет которых одинаковый (рис. 1).Известно, что четырехзвенный механизм, у которого все звенья в одном из крайних положений располага-ются по одной прямой, является механизмом с неопре-деленным движением [3]. Следовательно, в крайних положениях противолежащие подвижные звенья могут двигаться либо в одном, либо в противоположных на-правлениях. Для придания однонап...
The article discusses the methods for estimating the static definition of
The paper presents the results of development of an automated laboratory complex for the study of dynamic reactions of bearings of a rotating mechanical system. This complex includes an electromechanical model unit equipped with sensors for measuring reactions and angular speed of the system rotation, a power supply and control unit and a PC for processing the results of measurements and calculations of dynamic reactions. The theoretical basis for calculating the dynamic reactions of the unbalanced rotating mechanical system bearings is given, and a description of the research laboratory complex is provided. The results of experimental determination of these reactions as well as the corresponding calculated dependences of the latter on the angular speed of rotation and the degree of system unbalance are presented. The presence of a region of mechanical system insensitivity to its dynamic unbalance caused by the effects of friction in the bearings is confirmed. There is a good agreement between the proposed method for calculating dynamic reactions of rotating mechanical system bearings and experimental data on their measurement. The effectiveness of the developed laboratory complex in the training process at higher school when teaching the appropriate section of theoretical mechanics is noted.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.