The operation of a ball mill operating in a closed loop with a spiral classifier depends on the vacuum of the pulp in it, which is characterized by a solid / liquid ratio. Supply to the entrance of the ball mill at the same time ore and sand classifier, as well as changes in the circulating load in a wide range greatly complicate the definition of this technological parameter. This situation has led to the fact that the solid / liquid ratio in mills operating in such conditions can not be automatically adjusted, in turn, the deviation of the pulp vacuum from the required value leads to significant losses. The study of the ball mill as a controlled object on the pulp vacuum channel made it possible to describe it using the mathematical expression given in the article. The solution of this expression makes it possible to characterize the change in the mass of the material in the mill over time, provided that a stepwise action is introduced at the entrance - the volume flow of water or ore. A constant value of the mass of material in the mill will clearly characterize the corresponding solid/liquid ratio. It has been found that it is important to study the filtering capabilities of the control object, as control actions on water and disturbing actions on ore can significantly change the vacuum of the pulp in some areas of the mill. The filtering capabilities of the mill can be investigated by its amplitude frequency characteristics, which showed that at low circular frequencies the amplitude frequency characteristics depend on the mode of operation of the mill - the magnitude of the circulating load and the cost of the source ore. Using computer technology, spatial diagrams of the relative oscillations of the mass of material in the mill from the amplitude and frequency of influences at its entrance through the ore and water. In the course of theoretical research it was determined that the only approach to ensure the required accuracy of determining the solid / liquid ratio in these conditions is to filter the signals before applying to the input of the identification unit of the ratio. Thus, the system of automatic control of the solid/liquid ratio at the entrance to the mill is implemented on microprocessor means. Its operation on the laboratory test bench made on the microcontroller showed high accuracy of stabilization of technological parameter, reliability in various conditions of change of characteristics of input signals.
ВІРТУАЛЬНЕ ВИЗНАЧЕННЯ ХАРАКТЕРИСТИК ПОТОКУ В ПІСКОВОМУ ЖОЛОБІ ОДНОСПІРАЛЬНИХ КЛАСИФІКАТОРІВАктуальність. Бідні залізні руди, які потребують збагачення, є сировинною основою чорної металургії. Їх подрібнення у перших стадіях в наслідок перевитрати електроенергії, сталевих куль і футеровки погіршує конкурентоспроможність продукції. Зменшити перевитрати можливо автоматизацією цих процесів, однак перепоною на цьому шляху є нерозв'язаність задачі отримання інформації про піскове навантаження з необхідною точністю, хоч проводились широкі та тривалі дослідження. Прогресивний віртуальний підхід відкриває перспективи вирішення даної проблеми.Метою даної роботи є розробка математичної моделі віртуального визначення характеристик піскового потоку на виході механ-ічного односпірального класифікатора за технологічним параметром, який достатньо просто, точно та безконтактно можливо виміря-ти порівняно недорогим технічним засобом.Метод. Запропоновано метод графоаналітичного моделювання, де розглядається піскове тіло класифікатора (матеріал між двома сусідніми витками спіралі), яке подається горизонтальними та вертикальними шарами, створюючи вздовж висоти та довжини елементи l h Δ × Δ , що дозволяє отримувати залежності об'єму пісків у вертикальних шарах від довжини піскового тіла. Дані залежності при будь-якій висоті, кратній h Δ , що мають мінімум і максимум, апроксимувалися математичними виразами у вигляді семи членів ряду Фур'є. Вони встановлюють зв'язок між їх конкретними складовими та висотою піскового тіла. Використання даних зв'язків надає можливість знаходити миттєві об'ємні та масові витрати матеріалу в пісковий жолоб при будь-якому значенні висоти пісків. Результати. Отримана математична модель процесу розвантаження пісків у вигляді трьох основних і двадцяти двох додаткових рівнянь дозволяє визначати характеристики піскового потоку за висотою піскового тіла класифікатора. Миттєве значення витрати змінюється за достатньо складною залежністю, яка зберігається при різних висотах піскового тіла. При зростанні висоти закономірно збільшується як середнє, так і миттєве значення масової витрати пісків.Висновки. Вперше отримано математичну модель, яка описує значення миттєвої витрати пісків в процесі їх розвантаження у пісковий жолоб односпірального класифікатора за виміряною висотою піскового тіла. Завдяки цьому можливо стабілізувати розріджен-ня пульпи у кульовому млині, підвищити його продуктивність, якість подрібненого твердого та покращити експлуатаційні характери-стики технологічного обладнання і, як наслідок, зменшити перевитрати при подрібненні руд.Ключові слова: односпіральний класифікатор, миттєва масова витрата пісків, віртуальне визначення, математична модель. НОМЕНКЛАТУРАа 0 -вільний член тригонометричного поліному; а k -член тригонометричного поліному; В С -крок спіралі класифікатора; b k -член тригонометричного поліному; с -граничне значення кількості вертикальних шарів у пісковому тілі; D -символ операції перемноження; h Δ -висота горизонтальних шарів піскового тіла; h C -висота нижньої частини піскового тіла;...
Factors are identified whose role in increasing the productivity of ball mills is not fully disclosed. The criterion of optimality in the task of increasing the energy efficiency of ore grinding by ball mills and the influence of these factors on its value. Ways to improve the energy efficiency of ore grinding are proposed.
Дана публікація присвячена обґрунтуванню вторинного перетворювача системи контролю енергоефективності руйнування руди безпосередньо в барабані кульового млина. Первинним перетворювачем тут є пружна пластина, а прогин її центральної частини в наслідок руйнування руди при ударах куль через передаточний елемент – вихідною величиною, яка може фіксуватися або за переміщенням, або за деформацією. Існує широке коло засобів для вимірювання таких параметрів. Тому методом оптимізації на першому етапі дослідження відкидалися засоби, які об’єктивно не придатні для реалізації цих функцій. З залишку кілька засобів було вилучено шляхом аналізу. Далі досліджувались магнітоіндукційний і тензометричний перетворювачі. Аналізом доведено, що тензометричний перетворювач може виконувати функції вимірювання сигналу. Магнітоіндукційний перетворювач досліджувався методом моделювання. Показано, що він, забезпечений перетворювачем Холла, може фіксувати такі переміщення точно і за лінійною залежністю. Магнітоіндукційний перетворювач з обмоткою може давати додаткову інформацію про швидкість переміщення пружної пластини при ударі кулі. Обидва перетворювачі потребують установки проміжного передаточного елемента. Магнітоіндукційний – для забезпечення переміщення рухомого елемента з магнітном’якого матеріалу в площині, паралельній немагнітній прокладці, а тензометричний – для забезпечення деформування невеликої балки з двома ідентичними перетворювачами для компенсації впливу температури і підвищення чутливості.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.