The manufacture of stamp-welded and porous elements of porous-net material (PNM) from stainless steel 12H18N10T (0,12% C, 18% Cr, 10% Ni, 1% Ti) is difficult due to the low ductility under tension and the lack of weldability. It limits the use of PNM, although the fact that they may have the necessary technological and operational properties. The effect of porosity and heat conductivity anisotropy on the strength of welded splices of parts made of PNM have been established. Technologies of electron-beam welding (EBW) and sheet stamping of filter elements, which are implemented during the manufacture of prototypes of filter elements with a cleaning precision 10-12 microns, are presented.
Введение. Стремление увеличить надежность современных пнев-мо-и гидросистем приводит к повышению требований к чистоте ис-пользуемых в них жидкостей. При разработке конструкций фильтров важным этапом является обоснованный выбор или создание проница-емых элементов, которые должны обеспечивать необходимую тон-кость фильтрования (очистку), обладать высокой проницаемостью, быть стойкими и прочными во всем диапазоне рабочих температур и нагрузок, не ухудшать физико-химические показатели очищаемых сред и не загрязнять их частицами, вымываемыми из фильтроматериа-ла в процессе эксплуатации.Кроме того, необходимо обеспечить требуемую коррозионную стойкость фильтра. При этом пористые заготовки, используемые для изготовления фильтроэлементов, должны обладать необходимыми технологическими свойствами.Анализ выполненных в России и за рубежом работ, посвященных созданию пористых конструкционных материалов на металлической основе, показал, что для изделий, отвечающих сформулированным А.Ф. Третьяков
Введение. При изготовлении изделий из пористых материалов (ПМ) необходимо обеспечить получение не только заданной формы и размеров деталей, гидравлических характеристик и размеров пор проницаемых элементов, но и требуемых механических свойств. Ре-зультаты исследования порошковых, волокновых и сетчатых ПМ по-казали, что эксплуатационным требованиям функционирования эле-ментов систем охлаждения и ряда других изделий наиболее полно отвечают материалы, получаемые консолидацией металлических се-ток с применением горячей деформации в контролируемой газовой среде [1].Пористые материалы на основе металлических тканых проволоч-ных сеток, получившие название «пористые сетчатые материалы» (ПСМ) благодаря организованной структуре и сварке проволок сеток между собой, обладают стабильными и воспроизводимыми характери-стиками. При этом для ПСМ характерны более высокие механичес-кие и технологические свойства, чем для порошковых ПМ аналогич-ного химического состава.Листовые ПСМ применяют для изготовления изделий высокой прочности с требуемыми гидравлическими, фильтрующими и тепло-физическими свойствами. А.Ф. Третьяков 2 Инженерный журнал: наука и инновации # 62016Экспериментальные исследования штампуемости и свариваемо-сти ПСМ из стали 12Х18Н10Т показали, что более технологичными являются заготовки с высокой межслойной прочностью, низкой ани-зотропией механических свойств в плоскости листа. При этом уста-новлено, что формоизменение лимитируется не только опасностью разрушения в плоскости листа, но и возможностью расслоения заго-товки.Целью работы является изучение влияния конструкции брикета тканых сеток и технологических параметров сварки давлением про-волок сеток на межслойную прочность и механические свойства за-готовок в плоскости листа ПСМ, а также на штампуемость и сварива-емость материалов из стали 12Х18Н10Т.Межслойная прочность ПСМ. При исследовании механических характеристик применен структурный подход, который предполагает определение механических свойств исходя из геометрических пара-метров (типоразмера) сеток, их количества, взаимного расположения, механизма пластической деформации и качества консолидации структурообразующих элементов.Пористые элементы на основе металлических сеток представля-ют собой сварные конструкции, свойства которых определяются структурой материала проволок, их размерами, взаимным располо-жением, обжатием заготовок и полнотой образования твердофазных соединений на площадях контакта. Количество и площадь перекрес-тий проволок зависят от конструкций брикета сеток и механизма пластической деформации структурообразующих элементов при об-жатии.Конструкция брикета определяется типоразмером сеток, их ко-личеством и взаимным расположением. Геометрические параметры сеток зависят от типа переплетения проволок, диаметров основ d ос , утков d ут и расстояний между основами ос , l используя которые, мож-но получить два безразмерных параметра:для определения основных характеристик сеток независимо от их ти-поразмера. По типу переплетения проволочные тканые сетки разде-ляются на сетки с квадратными ячейкам...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.