Recently, many researchers focused on biocompability, corrosion resistance and properties behavior of implant materials in order to length the endoprostheses life. One of the rapid development areas of research is in the biomaterials field. Historically the uses of biomaterials has been to replace diseased or damaged tissues. This present paper reviews the research works carried out in the field of composite metal alloys reinforced with additive and to analyze the influence of modifying additive on mechanical properties of composite materials on the cobalt (Co), titanium (Ti) and magnesium (Mg) based alloy. The desirable mechanical properties of the matrix component compensate for the poor mechanical behavior of the biomaterials, while in turn the desirable bioactive properties of the additives improve those of metal alloys. The following additives were reviewed for research: poly methyl methacrylate (PMMA), fluoroapatite (FA) and bioglass. Results show that these composites can be the alternative materials for biomedical applications.
This research was carried out to fabricate and characterize Co-Cr-Mo (F-75) alloy. The samples have been prepared via solid state sintering. The lab work comprises the mixing of F-75 alloy powder with 2 wt. % of binder. The mixture was cold compacted using uniaxially press at 500 MPa. The samples were sintered at three different temperatures (1250 °C, 1300 °C and 1350 °C) in inert environment for 90 minutes of sintering time. The sintered samples were characterized by using Scanning Electron Microscope (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and optical microscope (OM) Olympus BX41M. Bulk density, apparent porosity, percentage of linear shrinkage, and microhardness of the samples were also characterized. The average of the grain sizes were measured by line intercepts method. The optical micrographs showed the difference grain size in all sintered samples after etching with Marble reagent. The result shows the percentage of linear shrinkage, bulk density value and porosity increase with increasing the sintering temperature. Beside that, higher sintering temperature yields coarser grain structure.
The Mg-1wt.%Ca alloy was fabricated using powder metallurgy method. The anodizing process were done by using different voltage (5V, 15V, 25V) and concentration of KOH (0.1M, 0.5M, 1.0M). The surface changes on PM Mg/1wt.%Ca resulted by anodizing was analyzed using SEM-EDX and XRD pattern. Meanwhile, surface hardness was measured by micro-Vickers hardness machine. The experiment found different XRD pattern between all non-anodized and anodized samples. The study found that increasing the voltage will increase the hardness while increasing KOH concentration reduced the hardness. The relation of the hardness and oxide film formation can be analyzed using SEM-EDX and XRD pattern. The optimum value for voltage, KOH concentration and hardness are 25V, 0.1M and 27.2 HV. The XRD detect the changes in PM Mg/1wt.% Ca indicates the oxide film formation.
Magnesium (Mg) has a great potential to be used in various field of work since it is lightweight and has low density properties. However, its application is limited due to its poor properties for Mg has a relatively low strength. Improvement is made by mixing Mg with calcium (Ca) as composite element for it is lightweight and non-toxic. In this research, Mg is prepared with different weight percentage (0, 0.5, 1, 1.5, 2 wt. %) of Ca with pure Mg as reference prepared by powder metallurgy (PM) method to study the mechanical properties. Morphological analysis carried out by optical microscope shows increase grain refinement with the increase of calcium content in Mg-Ca composites. The phase transition upon addition of Ca is determined using XRD method detects formation of Mg2Ca. Range from 1.78 g/cm3to 1.83 g/cm3, the density of each sample composite increase. While porosity profiles show inverse characteristics upon addition of Ca. Microhardness strengths also intensifies up to 193.20 MPa as more Ca content added in.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.