In this work, hydrogenated bisphenol A (HBPA) based dinitro mixed isomers (1a′ and 1a) were synthesized and separated via vacuum distillation under the monitor of DSC and 1H NMR. Corresponding diamines (2a′ and 2a) were separately polycondensed with five commercial dianhydrides via a two-step thermal imidization to obtain PI-(1′-5′) and PI-(1-5). All the polyimides could afford flexible, tough, and transparent films, and most of them were readily soluble not only in common polar solvents like DMAc, but also in low boiling point solvents such as chloroform. 1H NMR spectra of the polyimides demonstrated that HBPA moiety showed no conformation changes during the preparation of polymers. For a given dianhydride, PI-(1-5) exhibited better thermal stability than that of PI-(1′-5′), this can be attributed that the equatorial, equatorial C–O in PI-(1-5) promoted denser and more regular molecular chain stacking, as can be evidenced by the WAXD and geometric optimization results. Additionally, when the dianhydride was ODPA, BPADA or 6FDA, no apparent difference was found in either the transmittance or solubility between two series of polyimides, which could be attributed that twisted and flexible ether linkages, as well as bulky substituents, led to the “already weakened” inter- and intramolecular CT interaction and cohesive force. However, when it came to rigid and stiff dianhydride, e.g., BPDA, PI-3′ took an obvious advantage over PI-3 in transmittance and solubility, which was possibly owed to the larger molecular chain d-spacing imparted by equatorial, axial C–O. An overall investigation of PI-(1′-5′) and PI-(1-5) on aspects of thermal, mechanical, morphological, soluble and optical performance values was carried out, and the conformation effects of HBPA isomers on the properties of two series of polyimides were discussed in detail.

The theoretical calculation results of the condensation recovery rate and the required cooling power of an engineering application unit shown that condensation recovery of N2O4 in the waste gas is feasible and valuable in engineering applications.A simulation model was performed by using HYSYS and according to condensate-recovery process flow. Thus two important engineering parameters were simulated which included the thermal load of condensation system and the flow of glycol-water solution. The test results of an engineering application device based on these parameters at Jiuquan Satellite Launch Center indicated that the recovery efficiency can be above 90.0%, the purity of N2O4 recovered can be up to 99.6%.

In this work, 4,4′-isopropylidenedicyclohexanol (HBPA)-based dinitro isomers mixture (H″BPBN and H′BPBN) was synthesized and separated, and the structures of dinitro isomers were confirmed by differential scanning calorimetry and proton nuclear magnetic resonance spectroscopy. A series of copolyimides were prepared from diamino monomers with different percentages of novel diamine H″BPDA and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride via a conventional two-step procedure. All the copolyimides could afford flexible, tough, and transparent films with transmittance no less than 73% at 450 nm, which was attributed to the fact that nonplanar alicyclic diamine and the bulky and weakly polarizable trifluoromethyl hampered the formation of charge-transfer complex. Moreover, all the copolyimides were soluble not only in polar solvents such as N,N-dimethylformamide but also in low-boiling-point solvents such as dichloromethane, which was related to the fact that the existence of alicyclic diamine and bulky trifluoromethyl decreased the intermolecular force. In addition, the conformation effects of H″BPDA and H′BPDA on the aspects of thermal, mechanical, optical, and soluble performance of copolyimides were investigated and their structure–property relationships were discussed in detail.

No abstract

No abstract