Since 60-80% of total costs of production are usually associated with downstream collection, separation, and purification processes, it has become advantageous to investigate how to replace traditional methods with efficient and cost-effective alternative techniques for recovery and purification of biosurfactants. In the traditional techniques, large volumes of organic solvents are usually used for increasing production cost and the overall environmental burden. In addition, traditional production and separation methods typically carried out in batch cultures reduce biosurfactant yields due to product inhibition and lower biosurfactants activity as a result of interaction with the organic solvents used. However, some in situ recovery methods that allow continuous separation of bioproducts from culture broth leading to an improvement in yield production and fermentation efficiency. For biosurfactants commercialization, enhancement of product capacity of the separation methods and the rate of product removal is critical. Recently, interest in the integration of separation methods with a production step as rapid and efficient techniques has been increasing. This review focuses on the technology gains and potentials for the most common methods used in in situ product removal: foam fractionation and ultrafiltration, especially used to recover and purify two well-known biosurfactants: glycolipids (rhamnolipids) and lipopeptides (surfactins).

No abstract

Zirconium–Copper-based metallic glass thin films represent promising coatings in the biomedical sector for their combination of antibacterial property and wear resistance. However, finding a Zr–Cu metallic glass composition with desirable cytocompatibility and antibacterial property is extremely challenging. In this work, we have created a cytocompatible and (super-)hydrophobic Zr–Cu–Ag metallic glass coating with ≈95% antifouling properties. First, a range of different chemical compositions were prepared via Physical Vapor Deposition magnetron by co-sputtering Zr, Cu, and Ag onto a Polybutylene terephthalate (PBT) substrate among which Zr 93·5 Cu 6·2 Ag 0.2 , Zr 76·7 Cu 22·7 Ag 0.5, and Zr 69·3 Cu 30·1 Ag 0.6 were selected to be further investigate for their surface properties, antibacterial activity, and cytocompatibility. Scanning electron microscopy (SEM) images revealed a micro-roughness fibrous structure holding superhydrophobic properties demonstrated by specimens' static and dynamic contact angle measurements ranging from 130° to 150°. The dynamic contact angle measurements have shown hysteresis below 10° for all coated samples which indicated the superhydrophobicity of the samples. To distinguish between antifouling and bactericidal effect of the coating, ions release from coatings into Luria Bertani Broth (LB), and Dulbecco's Modified Eagle Medium (DMEM) solutions were evaluated by inductively coupled plasma mass spectrometry (ICP-MS) measurements after 24 ​h and 5 days. Antifouling properties were evaluated by infecting the specimens' surface with the Gram-positive Staphylococcus aureus and the Gram-negative Escherichia coli strain reporting a ≈95% reduction of bacteria adhesion as visually confirmed by FESEM and fluorescent live/dead staining. Human mesenchymal stem cells (hMSC) were used for direct cytocompatibility evaluation of coated samples and their metabolic activity was evaluated via relative fluorescence unit after 24 ​h and 5 days confirming that it was comparable to the controls (>97% viable cells). The results were further visualized by FESEM, fluorescent staining by Live/Dead Viability/Cytotoxicity Kit and confirmed the cytocompatibility of all coated samples. Finally, hMSC′ cytoplasm was stained by May Grunwald and Giemsa after 5days to detect and visualize the released ions which have diffused through the cells' membrane.

Implant-associated infections are a severe global concern, especially in the case of orthopedic implants intended for long-term or permanent use. The traditional treatment through systemic antibiotic administration is often inefficient due to biofilm formation, and concerns regarding the development of highly resistant bacteria. Therefore, there is an unfulfilled need for antibiotic-free alternatives that could simultaneously support bone regeneration and prevent bacterial infection. This study aimed to perform, optimize, and characterize the surface functionalization of Ti6Al4V-ELI discs by an FDA-approved antimicrobial peptide, nisin, known to hold a broad antibacterial spectrum. Accordingly, nisin bioactivity was also evaluated by in vitro release tests both in physiological and inflammatory pH conditions. Several methods, such as X-ray photoelectron spectroscopy (XPS), and Kelvin Probe atomic force microscopy confirmed the presence of a physisorbed nisin layer on the alloy surface. The functionalization performed at pH 6–7 was found to be especially effective due to the nisin configuration exposing its hydrophobic tail outwards, which is also responsible for its antimicrobial action. In addition, the first evidence of gradual nisin release both in physiological and inflammatory conditions was obtained: the static contact angle becomes half of the starting one after 7 days of soaking on the functionalized sample, while it becomes 0° on the control samples. Finally, the evaluation of the antibacterial performance toward the pathogen Staphylococcus aureus after 24 h of inoculation showed the ability of nisin adsorbed at pH 6 to prevent bacterial microfouling into biofilm-like aggregates in comparison with the uncoated specimens: viable bacterial colonies showed a reduction of about 40% with respect to the un-functionalized surface and the formation of (microcolonies (biofilm-like aggregates) is strongly affected.

Due to the rapid increase of waste vulcanized rubber products, the development of low-cost, efficient, and selective devulcanization processes is needed. In this paper, the devulcanization ability of Gordonia desulfuricans DSM 44462(T) was evaluated by a design of experiments. The aim of the experimental design was to investigate the importance of parameters influencing the bacterial growth, such as the glucose concentration (C), dibenzothiophene concentration (DBT), and initial biomass (optical density, OD) in biodevulcanization process. The complex viscosity (η*) was chosen as experimental response for the experimental design. A multiple linear regression was used to model the relationship between the response and the process variables. In addition, the crosslink density and gel fraction were measured. Furthermore, the automated ribosomal intergenic spacer analysis (ARISA) as a microbiological method was performed to assess the persistence of the inoculated strain during the experiments. Reduced regression models were obtained considering only the significant variables and interactions. The glucose concentration C and OD variables and C-DBT and DBT-OD interactions resulted to the relevant parameters for the process. The fingerprinting showed the persistence of G. desulfuricans DSM 44462(T), despite the presence of other bacterial population after the VGNR sterilization. These results highlight the importance to support the physics analysis with microbiological analyses to evaluate the bacterial persistence during the treatment.

No abstract

No abstract

No abstract