Polycrystalline‐silicon/oxide (poly‐Si/SiOx) passivating contacts for high efficiency solar cells exhibit excellent surface passivation, carrier selectivity, and impurity gettering effects. However, the ultrathin SiOx interlayer can act as a diffusion barrier for metal impurities and this potentially slows down the overall gettering rate of the poly‐Si/SiOx structures. Herein, the factors that determine the blocking effects of the SiOx interlayers are identified and investigated by examining two general types of the SiOx interlayers: 1.3 nm ultrathin tunneling SiOx with negligible pinholes and 2.5 nm SiOx with thermally created pinholes. Iron is used as tracer impurity in silicon to quantify the gettering rate. By fitting the experimental gettering kinetics by a diffusion‐limited segregation gettering model, the blocking effects of the SiOx interlayers are quantified by a transport parameter. Both the oxide stoichiometry and pinhole density affect the effective transport of iron through SiOx interlayers. The oxide stoichiometry depends strongly on the oxidation method, while the pinhole density is affected by the activation temperature, doping concentration, doping technique, and possibly the dopant type as well. To enable a fast gettering process during typical high‐temperature formation of the poly‐Si/SiOx structures, a SiOx interlayer that is less stoichiometric or with a higher pinhole density is preferred.
In addition to excellent surface passivation and carrier selectivity, the structure based on the heavily doped polysilicon layer on an ultrathin silicon oxide interlayer also demonstrates strong impurity gettering effects. Herein, the gettering strength of a range of phosphorus‐ or boron‐doped polysilicon films from different fabrication techniques is assessed and compared. Iron, one of the most common metallic impurities in silicon, is used as a tracer impurity to quantify the gettering strength (segregation coefficient). A comparison of the experimental results to the literature, combined with measurements of the electrically active and inactive dopant concentrations, enables us to suggest the main gettering mechanisms in different polysilicon films. The differences in the segregation coefficients of the phosphorus‐doped polysilicon films for iron are within one order of magnitude, in spite of their different combinations of gettering mechanisms. On the other hand, boron‐doped polysilicon films show a large variation in their gettering effects, although the predominant gettering mechanisms are all attributed to electrically inactive boron, according to the current understanding of the gettering mechanisms from the literature. Finally, the impact of different polysilicon gettering effects on the efficiency of tunnel oxide‐passivated contact (TOPCon) cells is simulated and discussed.
Metallic
impurities in the silicon wafer bulk are one of the major
efficiency-limiting factors in silicon solar cells. Gettering can
be used to significantly lower the metal concentrations. Although
gettering by silicon nitride films has been reported in literature,
much remains unknown about its gettering behaviors and mechanisms.
In this study, the gettering kinetics and mechanisms of silicon nitride
films, from both plasma-enhanced chemical vapor deposition (PECVD)
and low-pressure chemical vapor deposition (LPCVD), are investigated.
By monitoring the kinetics of iron loss from the silicon wafer bulk,
it is confirmed that silicon nitride gettering takes place mainly via segregation, even at a low annealing temperature of
400 °C. Simulation of the gettering kinetics
suggests the presence of an interfacial diffusion barrier in some
cases, which slows down the transport of iron impurities from the
silicon wafer bulk to the silicon nitride gettering regions. The activation
energy of the segregation gettering process is estimated to be 0.9
± 0.1 eV for the investigated PECVD silicon nitride film at 400–900
°C and 1.6 ± 0.5 eV for the investigated LPCVD silicon nitride
film at 400–700 °C.
Herein, a systematic study of the electronic quality of gallium‐doped p‐type silicon wafers from Czochralski‐grown ingots with melt recharging is presented. It is found that in the as‐grown state, the ingots contain interstitial iron concentrations in the range of 3 × 109–2 × 1010 cm−3, with a trend of slightly higher concentrations toward the tail end of each ingot, and in subsequently grown ingots. However, analysis of the effective lifetimes indicates that iron–gallium pairs are not the dominant recombination centers in the as‐grown state. Moreover, when these wafers are subjected to a tabula rasa step, an increase in the iron concentration is observed in the range of 1 × 1010–6 × 1010 cm−3, with iron–gallium pairs becoming the dominant recombination centers. This is possibly caused by the dissolution of pre‐existing precipitated iron in the wafers. Nevertheless, the negative impact of iron contamination can be dramatically reduced by subjecting the wafers to a phosphorus diffusion gettering step, as is commonly incorporated in the fabrication of p‐type passivated emitter and rear cells. Therefore, it is concluded that the quality of the ingots is not limited by iron contamination, even after multiple ingots are pulled from the recharged melt.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.