In this study, segmented thermoelectric generators (TEGs) have been simulated with various state-of-the-art TE materials spanning a wide temperature range, from 300 K up to 1000 K. The results reveal that by combining the current best p-type TE materials, BiSbTe, MgAgSb, K-doped PbTeS and SnSe with the strongest n-type TE materials, Cu-Doped BiTeSe, AgPbSbTe and SiGe to build segmented legs, TE modules could achieve efficiencies of up to 17.0% and 20.9% at ΔT = 500 K and ΔT = 700 K, respectively, and a high output power densities of over 2.1 Watt cm−2 at the temperature difference of 700 K. Moreover, we demonstrate that successful segmentation requires a smooth change of compatibility factor s from one end of the TEG leg to the other, even if s values of two ends differ by more than a factor of 2. The influence of the thermal radiation, electrical and thermal contact effects have also been studied. Although considered potentially detrimental to the TEG performance, these effects, if well-regulated, do not prevent segmentation of the current best TE materials from being a prospective way to construct high performance TEGs with greatly enhanced efficiency and output power density.

No abstract

Toward scalable manufacturing of perovskite solar panels, highperformance planar p−i−n perovskite solar cells (PVSCs) and modules have been demonstrated with blade coating and rapid thermal processing (RTP). The PVSCs made using RTP for less than 30 s have equivalent photovoltaic performance as devices fabricated from hot-plate annealing for 2 min. The resulting PVSCs show the best average power conversion efficiency (PCE) of over 18.47% from forward and reverse scans. Mini-modules with an active area of over 2.7 cm 2 exhibit a champion average PCE of over 17.73% without apparent hysteresis. To the best of our knowledge, these efficiencies are the highest for PVSCs processed by the combination of blade coating and RTP. Furthermore, both the blade coating and RTP were performed in an ambient environment, paving the way for the large-scale production of PVSCs through high-speed roll-to-roll printing.

No abstract

In organic bulk heterojunction solar cells (OSCs) donor-acceptor vertical composition profile is one of the crucial factors that affect power-conversion efficiency (PCE). In this simulation study, five different kinds of donor-acceptor vertical configurations, including sandwich type I and type II, charge transport favorable, charge transport unfavorable, and uniform vertical distribution, have been investigated for both regular and inverted OSC structures. OSCs with uniform and charge transport favorable vertical composition profiles demonstrate the highest efficiencies. High PCE from charge transport favorable configuration can be attributed to low recombination because of facilitated charge transport in active layer and collection at electrodes, while high PCE from uniform structure is due to sufficient interfaces for efficient exciton dissociation. OSCs with sandwich and charge transport unfavorable structures show much lower efficiencies. The physical mechanisms behind simulation results are explained based on energy band diagrams, dark current-voltage characteristics, and comparison of external quantum efficiency. In conclusion, experimental optimization of vertical composition profile should be directed to either uniform or charge transport favorable vertical configurations in order to achieve high-performance OSCs.

No abstract

The anisotropy of friction between 2D perovskites and the ITO is a four-fold symmetry in misaligned and aligned contacts.

A rapid layer‐specific annealing on perovskite active layer enabled by ultraviolet (UV) light‐emitting diode (LED) is demonstrated and efficiency close to 19% is achieved in a simple planar inverted structure ITO/PEDOT:PSS/MAPbI3/PC71BM/Al without any device engineering. These results demonstrate that if the UV dosage is well managed, UV light is capable of annealing perovskite into high‐quality film rather than simply damaging it. Different in principle from other photonic treatment techniques that can heat up and damage underlying films, the UV‐LED‐annealing method enables layer‐specific annealing because LED light source is able to provide a specific UV wavelength for maximum light absorption of target film. Moreover, the layer‐specific photonic treatment allows accurate estimation of the crystallization energy required to form perovskite film at device quality level.