A simple Clark-type online electrochemical cell design, consisting of a platinum gauze working electrode and incorporating ionic liquids (IL) as electrolytes, has been successfully applied for the amperometric sensing of oxygen. Studying ILs comprising the bis(trifluoromethylsulfonyl)imide anion, the obtained analytical parameters were found to be strongly dependent on the choice of cation. Compared with a conventional Clark cell design based on an aqueous supporting electrolyte, the modified oxygen sensor achieves substantial improvements in performance and stability. A limit of detection for oxygen as low as 0.05 vol %, linearity over an oxygen partial pressure between 0% and 20%, and a steady-state response time of 2 min was demonstrated, with a stable analytical response shown over the examined period of 90 days with no obvious fouling of the electrode surface. Based on the attractive physical attributes of ionic liquids (e.g., thermal stability beyond 150 °C), one can envision intriguing utility in nonstandard conditions and long-term online applications, as well as extension to the determination of other gases, such as methane and nitric oxide.

No abstract

Current sensor devices for the detection of methane or natural gas emission are either expensive and have high power requirements or fail to provide a rapid response. This report describes an electrochemical methane sensor utilizing a non-volatile and conductive pyrrolidinium-based ionic liquid (IL) electrolyte and an innovative internal standard method for methane and oxygen dual-gas detection with high sensitivity, selectivity, and stability. At a platinum electrode in bis(trifluoromethylsulfonyl)imide (NTf2)-based ILs, methane is electro-oxidized to produce CO2 and water when an oxygen reduction process is included. The in situ generated CO2 arising from methane oxidation was shown to provide an excellent internal standard for quantification of the electrochemical oxygen sensor signal. The simultaneous quantification of both methane and oxygen in real time strengthens the reliability of the measurements by cross-validation of two ambient gases occurring within a single sample matrix and allows for the elimination of several types of random and systematic errors in the detection. We have also validated this IL-based methane sensor employing both conventional solid macroelectrodes and flexible microfabricated electrodes using single- and double-potential step chronoamperometry.

Methane electro-oxidation was investigated and systematically characterized on three different electrodes (i.e. platinum, gold and carbon electrodes) with six different ionic liquids (ILs) by Cyclic Voltammetry (CV). At platinum electrode in bis(trifluoromethylsulfonyl)imide (NTf2) based ionic liquids (ILs), facile methane electro-oxidation is observed suggesting a unique catalytic Pt-NTf2 interface for electron transfer reaction of methane. Little methane electro-oxidation signal is observed in ILs with other anions. The final methane oxidation products in [C4mpy][NTf2] is confirmed to be CO2 and water by in-situ infrared spectroelectrochemistry. In contrast to many reported methane catalytic oxidation systems, there is no incomplete methane oxidation products observed. The electrochemical oxidation of methane at Pt and [C4mpy][NTf2] interface depends on the methane concentration linearly (from 1%∼10 vol.% methane concentration). The characteristic of peak potential shifts of the oxygen redox processes in the multiple cycle CV study is consistent with the electrode reaction of oxygen coupled with chemical reactions of CO2 and water which further confirms the products of methane electrode oxidation are CO2 and water. The cumulative results lead us to propose a mechanism suggesting a potential catalytic system of methane oxidation in NTf2 based ILs that strongly depends on the properties of the ILs and the electrode materials.

An eight-sensor array coupling a chemoselective room-temperature ionic liquid (RTIL) with quartz crystal microbalance (QCM) transduction is presented in this work in order to demonstrate the power of this approach in differentiating closely related analytes in sensory devices. The underlying mechanism behind the specific sensory response was explored by (i) studying mass loading and viscoelasticity effects of the sensing layers, predominantly through variation in damping impedance, the combination of which determines the sensitivity; (ii) creation of a solvation model based on Abraham's solvation descriptors which reveals the fact that polarizability and lipophilicity are the main factors influencing the dissolution of gas analytes into the RTILs; and (iii) determination of enthalpy and entropy values for the studied interactions and comparison via a simulation model, which is also effective for pattern discrimination, in order to establish a foundation for the analytical scientist as well as inspiration for synthetic pathways and innovative research into next-generation sensory approaches. The reported sensors displayed an excellent sensitivity with detection limit of <0.2%, fast response and recovery, and a workable temperature range of 27-55 °C and even higher. Linear discriminant analysis (LDA) showed a discrimination accuracy of 86-92% for nitromethane and 1-ethyl-2-nitrobenzene, 71% for different mixtures of nitromethane, and 100% for these analytes when thermodynamic parameters were used as input data. We envisage applications to detecting other nitroaromatics and security-related gas targets, and high-temperature or real-time situations where manual access is restricted, opening up new horizons in chemical sensing.

The bis(trifluoromethylsulfonyl)imide anion is widely used as an ionic liquid anion due to its electrochemical stability and wide electrochemical potential window at aerobic conditions. Here we report an innovative strategy by directly oxidizing bis(trifluoromethylsulfonyl)imide anion to form a radical electrocatalyst on platinum electrode at anaerobic condition. The in situ generated radical catalyst was shown to catalytically and selectively promote the electrooxidation of methanol to form methoxyl radical, in which the formation potential was drastically decreased with the existence of bis(trifluoromethylsulfonyl)imide radical. The electrochemically generated radical catalyst not only facilitates the oxidation of methanol but also provides good selectivity. The unique double layer structure of the 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([Bmpy][NTf2]) likely excludes the diffusion of larger molar mass molecules onto the electrode surface and enables the highly selective methanol oxidation at this IL–electrode interface. Cyclic voltammetry (CV) experiments were used to systematically characterize the details of the electrochemical processes with and without methanol in several other ILs, and a mechanism of the chemical and redox processes was proposed. This study provides a promising new approach for utilizing the unique properties of ionic liquids not only as solvents and electrolytes but also as the medium for in situ generation of electrocatalysts to promote methanol redox reactions for practical applications.

No abstract

The development of non-precious metal electrocatalysts for renewable energy conversion and storage is compelling but greatly challenging due to low activity of the existing catalysts. Herein, the ultrathin NiAl-layered double hydroxide nanosheets (NiAl-LDH-NSs) are prepared by simple liquid-exfoliation of bulk NiAl-LDHs and first used as ethanol electrooxidation catalysts. The ultrathin two-dimensional (2D) structure ensures that the LDH nanosheets expose a greater number of active sites. More importantly, much Ni(III) active species (NiOOH) in the ultrathin nanosheets are formed by the exfoliation process, which play an authentic catalytic role in the ethanol oxidation reaction (EOR). The presence of NiOOH remarkably improves the reactivity and electrical conductivity of LDH nanosheets. These synergistic effects lead to strikingly more than 30 times enhanced EOR activity of NiAl-LDH-NSs compared to bulk NiAl-LDHs. The obtained electrocatalytic activity is also much better than those of most Ni- and LDH-based EOR catalysts reported to date. In addition, the ultrathin NiAl-LDH-NS electrocatalyst also exhibits good long-term stability (maintain 81.8% of the original value after 10000 s). This study not only provides a highly competitive EOR catalyst, but also opens new avenues toward the design of highly efficient electrode materials that have various potential applications in supercapacitor, Ni-MH battery and other electrocatalytic systems.