No abstract

In this study, the change of the cooling rate in the range of about 0.1-1°C s -1 and the addition of Sr on the crystallization kinetics of the cast zinc alloys of the ZnAlCu type, as well as its relation to the microstructure were also investigated. Therefore, the aim of the rapid crystallisation is the achievement of materials with better properties, which can be obtained by refinement of the dendritic or eutectic microstructure, elimination of segregation, or creation of metastable phases and their morphology changes. In the investigated alloys, the change of cooling rate of 1°C s -1 has caused microstructure's refinement as well as increase in hardness. Increase in the cooling rate causes also morphology changes of the g ? a eutectic, and makes generally a global overcooling of the alloy as well as change in the temperatures at the beginning of crystallization T DN and of the alloy crystallization T S . The presented investigations concerning the electron microscopy methods, including transmission electron microscopy, allow revealing the crystallographic structure, based on the d-spacing changes, as well as the diffraction method used for phase determination, which is a helpful tool for the explanation of the important points in the thermo-derivative analysis curve, where the relation between the amount of phase and the occurrence of new phases can be determined.

Although Zn alloys are a very widely used material, there is a need for investigations concerning the influence of thermal conditions on its microstructure and its properties, which makes it useful for the specific tasks it has to fulfil for mass-produced items manufactured by the metalworking industry, in the automotive industry, as well as in countless electronic components. One of the possibilities is to create finer microstructures and enhance their properties, to change their chemical composition by adding alloying additives, and inoculation using modifiers. So in this paper, investigation results are presented concerning the influence of chosen alloying additives, such as Sr, Ce and Ti-B on the measured and calculated thermal characteristics and microstructure of zinc alloys with the addition of aluminium and copper. Based on the results on the phase and chemical composition of the cast Zn-Al-Cu alloys, inoculated with Sr and Ti-B, no differences were detected in the phase composition of the investigated alloys, owing to changes in cooling rates, which were chosen for the sample cooling process. A small amount of added cerium caused the occurrence of new phases present in the microstructure. Modification of the Zn-Al-Cu alloy precipitates changes in the thermomorphology of the phase and the 'tweed' type changes in the microstructure. Moreover, the addition of cerium causes a decrease in the temperature at the beginning (T L ) and the end of the solidification, as well as the occurrence of a multicomponent eutectic, which can be detected on the derivative curve.

For determination of the structure and properties of those alloys, the following investigations were carried out: scanning microscopy and EDS X-ray analysis. Investigations concerning the optimal chemical composition and production method of Cu-Ni-Si alloys modified by Cr and Re as well as the improved properties in comparison with traditional alloys contribute to better understanding of mechanisms influencing the improvement of mechanical properties of the newly developed alloys. Thermal analysis of the crystallization process allows for accurate calculation of latent heat of various phases developed during solidification. Based on the assumption that the latent crystallization heat is proportional to the share of various phases in the alloy, the thermo-derivative analysis also allows the calculation of the amount of crystallized phases. Calculation of the properties as mentioned earlier is based on the characteristic points determined in a derivative curve. The adequately selected chemical composition of the alloy, as well as the appropriate cooling rate and heat treatment conditions, leads to improvement of functional properties of manufactured elements. For the analysed alloys, a thermal derivative analysis was used to determine the kinetics of crystallization and the temperature of the beginning and the end of a phase and eutectic crystallization, mainly the liquidus temperature (T L) and solidus temperature (T SOL). The T SOL temperature determined on thermal derivative analysis is the upper limit of supersaturation of the tested alloys. The conductivity and microhardness of the tested alloys were also measured in the function of the chemical composition and the state (i.e., heat treatment).

The new high strength high electrical conductivity materials are demanded for advanced electric applications. Among them Cu-Ag and Cu-Nb wires are promising materials for generators of strong and variable magnetic fields production. Review of selected results of the studies into Cu-Ag and Cu-Nb based composite materials shows presence of various, not always well explained, mechanisms and phenomena which are observed during their production, examination and applications. Two classical copper alloys (with silver and with niobium) were selected for the investigations. The third material used in the studies was produced by bundle drawing of niobium wire in copper tube without classical melting and casting. Microstructure, mechanical and electrical properties were presented in relation to processing technology.

No abstract

Precipitation strengthened copper belongs to a group of functional and structural materials applied where combination of high electrical conductivity with high strength is required. A growing trend to use the new copper-based functional materials is observed recently world-wide. Within this group of materials particular attention is drawn to those with ultrafine grain size of a copper matrix.This study was aimed to investigate mechanical properties and microstructure in strips of age-hardenable copper alloys processed by continuous repetitive corrugation and straightening (CRCS).Tests were performed on 0.8 mm thick, CuCr0.6 and CuNi2Si1 alloys strips annealed at 650• C for 1 hour. The specially designed construction of die set (toothed rolls and plain rolls set) installed on tensile testing machine was applied for deformation process. The changes of mechanical properties (HV, ultimate tensile strength, 0,2 yield strength) as well as microstructure evolution versus number of deformation cycles were studied. The microstructure was observed with optical and electron microscopes (TEM and SEM equipped with EBSD).The CRCS process effectively reduced the grain size of CuCr0.6 and CuNi2Si1 alloys strips, demonstrating the CRCS as a promising new method for producing ultra-fine grained metallic strips.Keywords: copper alloy, severe plastic deformation, microstructure, mechanical properties Stopy miedzi utwardzane wydzieleniowo należą do grupy materiałów konstrukcyjnych stosowanych w sytuacji, gdzie wymagana jest wysoka elektryczna przewodność właściwa oraz wysokie właściwości wytrzymałościowe. Obecnie obserwuje się w świecie wzrastającą tendencję do stosowania nowych stopów miedzi. W tej grupie materiałów szczególne znaczenie odgrywają stopy cechujące się ultradrobnoziarnistą strukturą osnowy. W pracy badano właściwości mechaniczne oraz mikrostrukturę utwardzanych wydzieleniowo stopów miedzi odkształcanych metodą cyklicznego przeginania i prostowania. Badaniu poddano taśmy ze stopów miedzi CuCr0.6 and CuNi2Si1 o grubości 0,8 mm wyżarzanych w 650• C przez 1 godzinę. Cykliczne przeginanie i prostowanie zrealizowano na skonstruowanym do tego celu stanowisku zainstalowanym na maszynie wytrzymałościowej. Badaniu poddano zmiany właściwości mechanicznych taśmy (twardość HV, wytrzymałość na rozciąganie, umowna granica plastyczności), jak również zmiany mikrostruktury w zależności od ilości cykli deformacji. Badania mikrostruktur prowadzono za pomocą mikroskopii świetlnej i elektronowej (TEM i SEM wyposażony w EBSD)Proces cyklicznego przeginania i prostowania efektywnie zmniejszał wielkość ziaren taśm ze stopów CuCr0.6 CuNi2Si1, rokując dobre nadzieje jako metoda do otrzymywania struktury ultradrobnoziarnistej w płaskich wyrobach walcowanych.

Nowadays, there is much activity all over the world in development of Cu-Nb composites for their potential use as conductors in high field magnets. This study was aimed at investigation of microstructure, mechanical and electrical properties of Cu-Nb composite wires. The investigated materials have been processed by vacuum furnace melting and casting, and then hot forging and cold drawing. Initial results of research into Cu-Nb composite material obtained using repeated iterative drawing of niobium wires compacted into copper tube, have been also presented in this article. The ultimate tensile strength versus cold deformation degree has been presented. These changes have been discussed in relation to microstructure evolution. It was assumed that repeated drawing of compacted wires is a promising method for fibrous composite production (more than 823,000 Nb fibres of nanometric diameter) characterized by high mechanical properties and electrical conductivity. Original SPD technique applied for Cu-Nb composite deformation result in initial microstructure refinement and improves effectiveness of wire production process.Keywords: fibrous composite, copper alloy, mechanical properties, electrical conductivity, microstructureAktualnie obserwuje się na świecie intensywny rozwój kompozytów Cu-Nb stosowanych jako przewody nawojowe generatorów silnych pól magnetycznych. Badania miały na celu określenie mikrostruktury oraz właściwości mechanicznych i elektrycznych drutów kompozytowych Cu-Nb. Badane materiały wytworzono przez zastosowanie topienia i odlewania w piecu próżniowym, a następnie kucia na gorąco i ciągnienia. Zaprezentowano także wstępne wyniki badań wytwarzania kompozytu Cu-Nb na drodze iteracyjnego ciągnienia pakietu drutów niobowych w rurze miedzianej. Pokazano wyniki badań wytrzymałości na rozciąganie w zależności od stopnia odkształcenia, w powiązaniu ze zmianami mikrostruktury. Stwierdzono, że wielokrotne ciągnienie pakietu drutów jest obiecującą metodą wytwarzania kompozytów włóknistych (ponad 823000 włókien Nb o przekroju nanometrycznym) o wysokich właściwościach mechanicznych i konduktywności elektrycznej.