IntroductionRigid Ankle-Foot Orthoses (AFOs) are commonly prescribed to counteract excessive knee flexion during the stance phase of gait in children with cerebral palsy (CP). While rigid AFOs may normalize knee kinematics and kinetics effectively, it has the disadvantage of impeding push-off power. A spring-like AFO may enhance push-off power, which may come at the cost of reducing the knee flexion less effectively. Optimizing this trade-off between enhancing push-off power and normalizing knee flexion in stance is expected to maximize gait efficiency. This study investigated the effects of varying AFO stiffness on gait biomechanics and efficiency in children with CP who walk with excessive knee flexion in stance. Fifteen children with spastic CP (11 boys, 10±2 years) were prescribed with a ventral shell spring-hinged AFO (vAFO). The hinge was set into a rigid, or spring-like setting, using both a stiff and flexible performance. At baseline (i.e. shoes-only) and for each vAFO, a 3D-gait analysis and 6-minute walk test with breath-gas analysis were performed at comfortable speed. Lower limb joint kinematics and kinetics were calculated. From the 6-minute walk test, walking speed and the net energy cost were determined. A generalized estimation equation (p<0.05) was used to analyze the effects of different conditions. Compared to shoes-only, all vAFOs improved the knee angle and net moment similarly. Ankle power generation and work were preserved only by the spring-like vAFOs. All vAFOs decreased the net energy cost compared to shoes-only, but no differences were found between vAFOs, showing that the effects of spring-like vAFOs to promote push-off power did not lead to greater reductions in walking energy cost. These findings suggest that, in this specific group of children with spastic CP, the vAFO stiffness that maximizes gait efficiency is primarily determined by its effect on knee kinematics and kinetics rather than by its effect on push-off power.Trial RegistrationDutch Trial Register NTR3418

No abstract

No abstract

BackgroundAnkle-Foot-Orthoses with a ventral shell, also known as Floor Reaction Orthoses (FROs), are often used to reduce gait-related problems in children with spastic cerebral palsy (SCP), walking with excessive knee flexion. However, current evidence for the effectiveness (e.g. in terms of walking energy cost) of FROs is both limited and inconclusive. Much of this ambiguity may be due to a mismatch between the FRO ankle stiffness and the patient’s gait deviations.The primary aim of this study is to evaluate the effect of FROs optimised for ankle stiffness on the walking energy cost in children with SCP, compared to walking with shoes alone. In addition, effects on various secondary outcome measures will be evaluated in order to identify possible working mechanisms and potential predictors of FRO treatment success.Method/DesignA pre-post experimental study design will include 32 children with SCP, walking with excessive knee flexion in midstance, recruited from our university hospital and affiliated rehabilitation centres. All participants will receive a newly designed FRO, allowing ankle stiffness to be varied into three configurations by means of a hinge. Gait biomechanics will be assessed for each FRO configuration. The FRO that results in the greatest reduction in knee flexion during the single stance phase will be selected as the subject’s optimal FRO. Subsequently, the effects of wearing this optimal FRO will be evaluated after 12–20 weeks. The primary study parameter will be walking energy cost, with the most important secondary outcomes being intensity of participation, daily activity, walking speed and gait biomechanics.DiscussionThe AFO-CP trial will be the first experimental study to evaluate the effect of individually optimised FROs on mobility and participation. The evaluation will include outcome measures at all levels of the International Classification of Functioning, Disability and Health, providing a unique set of data with which to assess relationships between outcome measures. This will give insights into working mechanisms of FROs and will help to identify predictors of treatment success, both of which will contribute to improving FRO treatment in SCP in term.Trial registrationThis study is registered in the Dutch Trial Register as NTR3418.

In children with cerebral palsy (CP), rigid ventral shell ankle-foot orthoses (vAFOs) are often prescribed to reduce excessive knee flexion in stance and lower the energy cost of walking (ECW). However, how vAFOs affect ECW is a complex issue, as vAFOs may have an impact on lower limb biomechanics, upper body movements, and balance. Besides, the vAFO's biomechanical effect have been shown to be dependent on its stiffness around the ankle joint. We examined whether vAFO stiffness influences trunk movements and gait stability in CP, and whether there is a relationship between these factors and ECW. Fifteen children with spastic CP were prescribed vAFOs. Stiffness was varied into a rigid, stiff and flexible configuration. At baseline (shoes-only) and for each vAFO stiffness configuration, 3D-gait analyses and ECW-tests were performed. From the gait analyses, we derived trunk tilt, lateroflexion, and rotation range of motion (RoM) and the mediolateral and anteroposterior Margins of Stability (MoS) and their variability as measures of gait stability. With the ECW-test we determined the netEC. We found that wearing vAFOs significantly increased trunk lateroflexion (Wald c2 ¼ 33.7, p < 0.001), rotation RoM (Wald c2 ¼ 20.5, p < 0.001) and mediolateral gait instability (Wald c2 ¼ 10.4, p ¼ 0.016). The extent of these effects partly depended on the stiffness of the vAFO. Significant relations between trunk movements, gait stability and ECW were found r ¼ 0.57e0.81, p < 0.05), which indicates that trunk movements and gait stability should be taken into account when prescribing vAFOs to improve gait in children with CP walking with excessive knee flexion.

Objective Hand orthoses are often prescribed for persons with chronic hand and wrist impairments. This study assessed the feasibility, in terms of production time and user satisfaction, of 3-dimensional printed hand orthoses compared with conventional hand orthoses for this population. Methods In this prospective case series, both a conventional hand orthosis and a 3-dimensional printed hand orthosis were manufactured for 10 participants. Production time (in minutes) of each orthosis was recorded. Each orthosis was worn for one week, after which participants completed a self-designed questionnaire on satisfaction, scored on a 5-point Likert scale. Functionality and orthosis preference were also assessed. Results The mean (standard deviation (SD)) production time for the 3-dimensional printed orthoses, of 112 (11.0) min, was significantly shorter compared with 239 (29.2) min for the conventional orthoses (95% confidence interval (95% CI) 71–182 min, p = 0.001). Satisfaction scores were similar for both orthoses, except for comfort item “fitting method”, which was rated significantly higher for scanning compared with casting (median [IQR] score: 5 [0.0]; 4 [2.0], p = 0.034). Functionality and orthosis preference were rated similar for both orthoses. CONCLUSION As the production time was halved, user satisfaction similar, and scanning experienced as slightly more comfortable than casting, 3-dimensional printed hand orthoses seem feasible and potentially beneficial for use in people with chronic hand and wrist impairments. LAY ABSTRACT Persons with chronic hand and wrist impairments often use an orthosis to make it easier to perform daily activities. Three-dimensional scanning and printing can facilitate the manufacturing of hand orthoses. This study compared 3-dimensional printed orthoses with conventional orthoses for persons with chronic hand and wrist impairments, with regard to production time and user satisfaction. Ten participants used a 3-dimensional printed orthosis, as well as a conventional orthosis, each for one week. The results showed that production time of 3-dimensional printed orthoses was half that of conventional orthoses. Satisfaction with both orthoses was similar, except for the “fitting method”, whereby fitting by 3-dimensional scanning was perceived as slightly more comfortable compared with conventional casting. Functionality and orthosis preference were rated similar for both orthoses. In conclusion, 3-dimensional printed orthoses appear to be a potential treatment option for persons with chronic hand and wrist impairments.

No abstract

A rigid ventral shelf ankle foot orthosis (AFO) may improve gait in children with spastic cerebral palsy (SCP) whose gait is characterized by excessive knee flexion in stance. However, these AFOs can also impede ankle range of motion (ROM) and thereby inhibit push-off power. A more spring-like AFO can enhance push-off and may potentially reduce walking energy cost. The recent development of an adjustable spring-hinged AFO now allows adjustment of AFO stiffness, enabling tuning toward optimal gait performance. This study aims to quantify the mechanical properties of this spring-hinged AFO for each of its springs and settings. Using an AFO stiffness tester, two AFO hinges and their accompanying springs were measured. The springs showed a stiffness range of 0.01-1.82 N · m · deg(-1). The moment-threshold increased with increasing stiffness (1.13-12.1 N · m), while ROM decreased (4.91-16.5°). Energy was returned by all springs (11.5-116.3 J). These results suggest that the two stiffest available springs should improve joint kinematics and enhance push-off in children with SCP walking with excessive knee flexion.