Nickel-rich layered materials LiNi 1-x-y Mn x Co y O 2 are promising candidates for high energy density lithium-ion battery cathodes. Unfortunately, they suffer from capacity fading upon cycling, especially with high voltage charging. It is critical to have mechanistic understanding of such fade. Herein, synchrotron-based techniques (including scattering, spectroscopy, and microcopy) and finite element analysis were utilized to understand the LiNi 0.6 Mn 0.2 Co 0.2 O 2 material from structural, chemical, morphological, and mechanical points of view. The lattice structural changes are shown to be relatively reversible during cycling, even when 4.9V charging was applied. However, local disorder and strain were induced by high voltage charging. Nano-resolution 3D transmission X-ray microscopy data analyzed by machine learning methodology reveals that high-voltage charging induced significant oxidation state inhomogeneities in the cycled particles. Regions at the surface have rock-salt type structure with lower oxidation state and build up the impedance while regions with higher oxidization state are scattered in the bulk and are likely deactivated during cycling. In addition, the development of micro-cracks is highly dependent on the pristine state morphology and cycling conditions. Hollow particles seem to be more robust against stress-induced cracks than the solid ones, suggesting that morphology engineering can be effective in mitigating the crack problem in these materials. The engineering support from D. Van Campen, V. Borzenets and D. Day for the TXM experiment at beamline 6-2C of SSRL is gratefully acknowledged. The work done at Brookhaven National Laboratory was supported by the Assistant Secretary for Energy Efficiency and Renewable Energy, Vehicle Technology Office of the U.S. Department of Energy through the Advanced Battery Materials Research (BMR) Program, including Battery500 Consortium under contract DE-SC0012704. This research used beamlines 7-BM and 28-ID-2 of the National Synchrotron Light Source II, a U.S.

Functional materials and devices are usually morphologically complex and chemically heterogeneous. Their structures are often designed to be hierarchical because of the desired functionalities, which usually require many different components to work together in a coherent manner. The lithium ion battery, as an energy storage device, is a very typical example of this kind of structure. In a lithium ion battery, the cathode, anode, and separator are soaked in a liquid electrolyte, facilitating the back and forward shuttling of the lithium ions for energy storage and release. The desired performance of a lithium ion battery has many different aspects that need to be engineered and balanced depending on the targeted applications. In most cases, the cathode material has become the limiting factor for further improvements and, thus, has attracted intense attention from the research community. While the improvement in the overall performance of the lithium ion battery is the ultimate goal of the research in this field, understanding the relationship between the microscopic properties and the macroscopic behaviors of the materials/devices can inform the design of better battery chemistries for practical applications. As a result, it is of great fundamental and practical importance to investigate the electrode materials using experimental probes that can provide good chemical sensitivity and sufficient spatial resolution, ideally, under operating conditions. With this motivation, our group has been focusing on the development of the nanoscale full-field X-ray spectro-microscopy, which has now become a well-recognized tool for imaging battery electrode materials at the particle level. With nanoscale spatial resolution, this technique can effectively and efficiently tackle the intrinsically complicated mesoscale chemistry. It allows us to monitor the particles' morphological and chemical evolution upon battery operation, providing valuable insights that can be incorporated into the design of new battery chemistries. In this Account, we review a series of our recent studies of battery electrode materials using nanoscale full-field X-ray spectro-microscopy. The materials that are the subjects of our studies, including layer-structured and spinel-structured oxide cathodes, are technically very important as they not only play an important role in today's devices but also possess promising potential for future developments. We discuss how the subparticle level compositional and state-of-charge heterogeneity can be visualized and linked to the bulk performance through systematic quantification of the imaging data. Subsequently, we highlight recent ex situ and in situ observations of the cathode particles' response to different reaction conditions, including the spontaneously adjusted reaction pathways and the morphological changes for the mechanical strain release. The important role of surface chemistry in the system is also discussed. While the microscopic investigation at the particle level provides useful insights, the degree...