We present here detailed mechanistic studies of electrocatalytic hydrogenation (ECH) in aqueous solution over skeletal nickel cathodes to probe the various paths of reductive catalytic C–O bond cleavage among functionalized aryl ethers relevant to energy science. Heterogeneous catalytic hydrogenolysis of aryl ethers is important both in hydrodeoxygenation of fossil fuels and in upgrading of lignin from biomass. The presence or absence of simple functionalities such as carbonyl, hydroxyl, methyl, or methoxyl groups is known to cause dramatic shifts in reactivity and cleavage selectivity between sp3 C–O and sp2 C–O bonds. Specifically, reported hydrogenolysis studies with Ni and other catalysts have hinted at different cleavage mechanisms for the C–O ether bonds in α-keto and α-hydroxy β-O-4 type aryl ether linkages of lignin. Our new rate, selectivity, and isotopic labeling results from ECH reactions confirm that these aryl ethers undergo C–O cleavage via distinct paths. For the simple 2-phenoxy-1-phenylethane or its alcohol congener, 2-phenoxy-1-phenylethanol, the benzylic site is activated via Ni C–H insertion, followed by beta elimination of the phenoxide leaving group. But in the case of the ketone, 2-phenoxyacetophenone, the polarized carbonyl π system apparently binds directly with the electron rich Ni cathode surface without breaking the aromaticity of the neighboring phenyl ring, leading to rapid cleavage. Substituent steric and electronic perturbations across a broad range of β-O-4 type ethers create a hierarchy of cleavage rates that supports these mechanistic ideas while offering guidance to allow rational design of the catalytic method. On the basis of the new insights, the usage of cosolvent acetone is shown to enable control of product selectivity.

Lignin may serve as a renewable feedstock for the production of chemicals and fuels if mild, scalable processes for its depolymerization can be devised. The use of small organic thiols represents a bioinspired strategy to cleave the β‐O‐4 bond, the most common linkage in lignin. In the present study, synthetic β‐O‐4 linked polymers were treated with organic thiols, yielding up to 90 % cleaved monomer products. Lignin extracted from poplar was also treated with organic thiols resulting in molecular weight reductions as high as 65 % (Mn) in oxidized lignin. Thiol‐based cleavage of other lignin linkages was also explored in small‐molecule model systems to uncover additional potential pathways by which thiols might depolymerize lignin. The success of thiol‐mediated cleavage on model dimers, polymers, and biomass‐derived lignin illustrates the potential utility of small redox‐active molecules to penetrate complex polymer matrices for depolymerization and subsequent valorization of lignin into fuels and chemicals.

This is the author manuscript accepted for publication and has undergone full peer review but has not been through the copyediting, typesetting, pagination and proofreading process, which may lead to differences between this version and the Version of Record.

Diaryl ethers undergo electrocatalytic hydrogenolysis (ECH) over skeletal Ni cathodes in a mild, aqueous process that achieves direct C-O cleavage without initial benzene ring saturation. Mechanistic studies find that aryl phenyl ethers with a single para or meta functional group (methyl, methoxy, or hydroxy) are selectively cleaved to the substituted benzene and phenol, in contrast to recently reported homogeneous catalytic cleavage processes. Ortho positioning of substituents reverses this C-O bond selectivity, except for the 2-phenoxyphenol case. Together with isotope labeling and co-solvent studies, these results point to two distinct cleavage mechanisms: (a) dual-ring coordination and C-H activation, leading to vicinal elimination to form phenol and a surface-bound aryne intermediate which is then hydrogenated and released as the arene; and (b) surface binding in keto form by the phenolic ring of the hydroxy-substituted substrates, followed by direct displacement of the departing phenol. Notably, acetone inhibits the well-known reduction of phenol to cyclohexanol, affording control of product ring saturation. A byproduct of this work is the discovery that the ECH treatment completely defluorinates substrates bearing aromatic C-F and C-CF3 groupings.

The formation of carbon-carbon bonds by pinacol coupling of aldehydes and ketones requires a large negative reduction potential, often realized with a stoichiometric reducing reagent. Here, we use solvated electrons generated via a plasmaliquid process. Parametric studies with methyl-4-formylbenzoate reveal that selectivity over the competing reduction to the alcohol requires careful control over mass transport. The generality is demonstrated with benzaldehydes, benzyl ketones, and furfural. A reaction-diffusion model explains the observed kinetics, and ab initio calculations provide insight into the mechanism. This study opens the possibility of a metal-free, electrically-powered, sustainable method for reductive organic reactions.

New diamine, 4-(4-diphenylphosphino)phenyl-2,6-bis(4-aminophenyl)pyridine, was prepared, and the related polyamides (PAs) bearing 2,6-diphenylpyridyl units and pendant diphenylphosphinophenyl groups were synthesized by direct polycondensation of this diamine and various aromatic diacids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. The resulting PAs with inherent viscosities of 0.78–1.06 dL g−1 are readily soluble in polar aprotic solvents such as NMP, N, N-dimethylacetamide, and dimethylsulfoxide as well as less polar solvents such as m-cresol and pyridine. All the PAs are amorphous and could be solution-cast into transparent, flexible, and tough films, which have tensile strengths of 68.2–88.8 MPa, tensile moduli of 1.9–2.4 GPa, and elongations at break of 5.4–10.3%. These polymer films also exhibit high optical transparence with the UV cutoff wavelength in the 361–412 nm range. These PAs display glass transition temperatures of 316–332°C, 10% mass loss temperatures of 524–553°C, and more than 48% residues at 800°C in nitrogen, respectively. Their high char yields and good limited oxygen index values ranging from 39 to 44 indicate the prepared PAs show good thermal stability and flame-retardant property.

A new aromatic diacid monomer, N, N-bis(4-carboxyphenyl)-4-trifluoromethylaniline, was synthesized by the substitution reaction of 4-trifluoromethylaniline with 4-fluorobenzonitrile, followed by alkaline hydrolysis of the dinitrile intermediate. Several polyamides with 4-trifluoromethyltriphenylamine moieties were prepared from the diacid and various aromatic diamines via the direct phosphorylation polycondensation. All the polyamides were amorphous and readily soluble in many polar organic solvents such as N, N-dimethylacetamide and N-methyl-2-pyrrolidone, and could be solution-cast into transparent, tough, and flexible films with good mechanical properties. They exhibited good thermal stability with glass transition temperatures of 260–330°C, 10% weight-loss temperatures above 500°C, and char yields higher than 60% at 800°C in nitrogen. These polymers had low dielectric constants of 3.35–3.72 (100 Hz), low water uptake of 1.80–2.60%, and high transparency with an ultraviolet–visible absorption cutoff wavelength in the range of 378–390 nm. Cyclic voltammograms of the polyamide films cast onto an indium-tin oxide–coated glass substrate exhibited a reversible oxidation redox coupled with oxidation half-wave potentials ( E 1/2) of 0.95–1.04 V versus silver/silver chloride in an acetonitrile solution.

A series of new polyarylates bearing cardo xanthene groups were synthesized by phase-transfer-catalyzed interfacial polycondensation of 9,9-bis[4-(4-chloroformylphenoxy)phenyl]xanthene with various bisphenols containing the isopropylidene, hexafluoroisopropylidene, 1-phenylethylidene, diphenylmethane, cyclohexane, and xanthene structures. High-molecular-weight polyarylates with number-average molecular weight and polydispersity index in the range of 30,100–35,300 and 1.82–2.17, respectively, exhibited high glass transition temperatures ranged from 226°C to 261°C, and their 10% weight loss temperatures were in the range of 421–452°C with char yields above 45% at 700°C in nitrogen. All the polyarylates were amorphous and readily soluble in organic solvents such as dichloromethane, chloroform, tetrahydrofuran, meta-cresol, pyridine, N,N-dimethylformamide, N,N-dimethylacetamide, and 1-methyl-2-pyrrolidinone at room temperature and could be cast into tough, transparent, and flexible films with tensile strengths of 85.6–108.3 MPa, elongations at break of 2–3%, and tensile moduli of 7–9 GPa.