A fixed PDC cutting element creates an inherent limitation because only a small portion of the diamond table contacts formation and as the cutter wears/chips, drilling efficiency declines. It is well documented that wear flats generate a high degree of frictional heat which breaks down the diamond bond and in extreme cases can even convert synthetic diamond back to graphite.To solve the issue a research initiative was launched to investigate different methods to enable a PDC shearing element to fully rotate while drilling to increase overall cutting efficiency and bit life. Engineers investigated different retention methods and cutting structure designs to create the optimal driving force to accomplish the objective. Several designs were implemented that hold the cutter securely in place and allow full cutter rotation. These assemblies were modeled using an FEA-based system and then tested in the laboratory to evaluate function and strength. Experiments confirmed the new rolling cutter (RC) was able to shear an extended section of rock with a consistent force level (lbs). Conversely, the traditional fixed-cutter assembly required steadily increased force to drive the cutter the same distance. Examination of the rolling cutter's dull condition clearly indicated significantly improved durability and cutting efficiency.The recent introduction of a new rolling cutter PDC bit that utilizes the entire 360° of diamond edge has delivered positive results in field trials. Initial testing was targeted at the highly abrasive Granite Wash formation in Western Oklahoma/Texas Panhandle where cutter wear is the predominant failure mechanism. Application challenges include low ROP and premature tripping for a new bit. A six-bladed prototype PDC bit was manufactured with rolling cutters strategically positioned in the shoulder area. The bit was run on a steerable motor through the horizontal interval with good results increasing total footage and ROP capabilities.In the central USA the rolling cutter has been run more than 70 times and has increased average footage totals by 56% compared to 450 offsets drilled with conventional fixed cutter PDC bits from various manufacturers. The authors will present results of field tests and two case studies that document performance improvement in these challenging drilling environments. They will also outline plans for future development.
Extended footage capabilities and high rate of penetration give PDC bits a distinct advantage over rollercone bits in many applications. However, the fixed PDC element creates an inherent limitation because only a small portion of the cutter contacts the formation, and as the cutters wear/chip drilling efficiency declines. The industry requires new technology that can effectively utilize the entire 360° diamond cutting edge to reduce frictional heat/wear while increasing drilling efficiency and bit life. A plan was initiated to rotate the cutter while drilling and engineers investigated different retention methods and cutting structure designs to create the optimal driving force to accomplish the objective. Several designs were implemented that hold the cutter securely in place and allow full cutter rotation. These assemblies were extensively modeled using FEA and laboratory tested to evaluate function and strength. In a test apparatus, the new shearing element (rolling cutter/RC) was able to cut an extended section of rock with a consistent force level (lbs). Conversely, the traditional fixed-cutter assembly required steadily increased force to drive the cutter the same distance. Examination of the rolling cutter's dull condition clearly indicated significantly improved durability and cutting efficiency. Initial field testing targeted the highly abrasive Granite Wash formation in Western Oklahoma/Texas Panhandle where cutter wear is the predominant failure mechanism. Application challenges include slow ROP and premature tripping for a new bit. A six-bladed prototype PDC bit was manufactured with three rolling cutters positioned in the shoulder area. The bit was run on a steerable motor through the horizontal interval with good results. The next prototype was equipped with additional RCs and drilled more footage compared to offset average. Additional experiments are being conducted with RCs which will continue to increase performance. The authors will present several case studies which will document performance improvement in challenging drilling environments.
A fixed PDC element creates an inherent limitation because only a small portion of the cutter contacts formation and as the cutter wears/chips drilling efficiency declines. It is well documented that wear flats generate a high degree of frictional heat which breaks the diamond bond. To solve the issue an R&D initiative was launched to investigate different methods to enable a PDC shearing element to rotate while drilling to increase overall cutting efficiency and bit life. Engineers investigated different retention methods to create the optimal driving force and allow full cutter rotation. The assemblies were modeled using an FEA based engineering system and then tested in the laboratory to evaluate function and strength. Experiments confirmed the new rolling cutter (RC) was able to shear an extended section of rock with a consistent force level (lbs). A traditional fixed-cutter assembly required steadily increased force to drive the cutter the same distance. Examination of the rolling cutter's dull condition clearly indicated significantly improved durability and cutting efficiency. The recent introduction of a new rolling cutter PDC bit that utilizes the entire 360° of diamond edge has delivered positive results in field trials. Initial testing was targeted at the highly abrasive Granite Wash formation in Western Oklahoma/Texas Panhandle where cutter wear is the predominant failure mechanism. A six-bladed prototype PDC bit, with three rolling cutters positioned in the shoulder area was run on PDM and increased total footage capabilities compared to conventional PDC. The next prototypes were equipped with a smaller, yet more robust generation-3 retaining device. Starting in Q4 2012, the total RC count/bit was progressively increased on five/six bladed designs from 3, 5, 7, 10 and then 12. The 13mm designs are consistently exceeding footage totals compared to offsets in central USA, North Dakota and Canada. In central USA, which contains the largest data set (13 RC runs) the rolling cutter has increased average footage totals by 34.4% compared to offsets drilled with standard PDC from various manufacturers. Case studies will document performance improvement in these challenging drilling environments. The authors will discuss plans to develop a rolling cutter bit to extend lateral run length in an abrasive Middle East formation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.