SummaryThe application of resin composites in dentistry has become increasingly widespread due to the increased aesthetic demands of patients, improvements in the formulation of resin composites, and the ability of these materials to bond to tooth structures, together with concerns about dental amalgam fillings. As resistance to wear is an important factor in determining the clinical success of resin composite restoratives, this review article defines what constitutes wear and describes the major underlying phenomena involved in this process. Insights are further included on both in vivo and in vitro tests used to determine the wear resistance of resin composite and the relationships between these tests. The discussion focuses on factors that contribute to the wear of resin composite. Finally, future perspectives are included on both clinical and laboratory tests and on the development of resin composite restorations.

In this study, dentin bond fatigue resistance and interfacial science characteristics of universal adhesives through etch-and-rinse and self-etch modes were investigated. Resin composite was bonded to human dentin with four universal adhesives, namely, Adhese Universal, All-Bond Universal, G-Premio Bond, and Scotchbond Universal Adhesive. The initial bond strengths, bond fatigue strengths, and interfacial science characteristics of the universal adhesives with dentin through etch-and-rinse and self-etch modes were determined. Bond fatigue resistance (initial bond strength and bond fatigue strength) of universal adhesives in etch-and-rinse mode showed no significant difference in contrast to that in self-etch mode and was material-dependent regardless of the etching mode. Although phosphoric acid conditioning of dentin did not have a strong impact on the bond fatigue resistance, surface free energy and parameters of dentin were significantly decreased by etching and by application of universal adhesives regardless of etching mode. Changes in γ S and γ S h for when universal adhesive was applied to etched and ground dentin were significantly different depending on the adhesive. The results suggest that bonding performance of universal adhesives was effective in both etching modes; however, bonding mechanisms may be different for each. Keywords; light-curing of dental adhesives, dental debonding, dental etching, dental restoration failure, dental stress analysis Materials and Methods Study materials Four universal adhesives were used in this study: (i) Adhese Universal (AU, Ivoclar Vivadent, Schaan, Liechtenstein), (ii) All-Bond Universal (AB, Bisco, Schaumburg, IL, USA), (iii) G-Premio Bond (GB, GC, Tokyo, Japan), and (iv) Scotchbond Universal Adhesive (SU, 3M Oral Care). Ultra-Etch (Ultradent, South Jordan, UT, USA) was used as a 35% phosphoric acid pre-etching agent and Z100 Restorative (3M Oral Care) as the resin composite employed to make specimens. Table 1 lists the tested materials and their lot numbers and components. Specimen preparation This study used de-identified extracted human molar teeth. To comply with research ethics, the protocol was reviewed and approved by the Ethics Committee for Human Studies of NU (#2015-06) and Biomedical Institutional Review Board at CU (#760765-1). Preparation of the teeth was done in the manner described in the study by Nagura et al. [18], except that a flat dentin surface, rather than enamel surface, was prepared. Specimens with and without etching were prepared for each adhesive, giving a total of eight experimental groups for each of the procedures performed (Table 2). Initial bond strength testing Initial bond strength testing was carried out as described by Nagura et al. [18]. Bond fatigue strength testing Bond fatigue strength testing was carried out as described by Nagura et al. [18].

The effect of phosphoric acid pre-etching on enamel bond fatigue durability of universal adhesives and two-step self-etch adhesives was investigated. Four universal adhesives and three two-step self-etch adhesives were used. The initial shear bond strengths and shear fatigue strengths to enamel with and without phosphoric acid pre-etching using the adhesives were determined. SEM observations were also conducted. Phosphoric acid pre-etching of enamel was found to increase the bond fatigue durability of universal adhesives, but its effect on two-step self-etch adhesives was material-dependent. In addition, some universal adhesives with phosphoric acid preetching showed similar bond fatigue durability to the two-step self-etch adhesives, although the bond fatigue durability of universal adhesives in self-etch mode was lower than that of the two-step self-etch adhesives. Phosphoric acid pre-etching enhances enamel bond fatigue durability of universal adhesives, but the effect of phosphoric acid pre-etching on the bond fatigue durability of two-step self-etch adhesives was material-dependent.

No abstract

The aim of this study was to use ultrasonography to evaluate the effect of the self-assembling peptide P11-4 on acid erosion prevention. Curodont Repair (CR), which includes peptide P11-4, was used. Rectangular prisms of bovine enamel (4×1×1 mm) were immersed in pure orange juice for a period of 5 minutes six times per day for 28 days. These samples were divided into four groups of six specimens each and treated differently for an additional period of 28 days: 1) baseline group specimens were stored in artificial saliva; 2) CR group specimens were exposed to curodont without acid challenge; 3) NCRA (no curodont+acid challenge) specimens were treated with orange juice without curodont exposure; and 4) CRA (CR+acid challenge) specimens were treated with curodont before treatment with orange juice. The propagation time of longitudinal ultrasonic velocity (UV) was measured. Ultrastructural observation of each tested enamel surface was carried out using field-emission scanning electron microscopy (SEM). The UV data were analyzed using two-way analysis of variance with time and treatment as confounding factors. Post hoc pairwise tests among groups were performed using the Tukey honestly significant difference test. The average UV in intact bovine enamel for the baseline group ranged from 4,483 to 4,549 m/s and did not vary significantly within the test period. The average ultrasonic velocity (UV) in all samples decreased after the initial erosion. The UV in NCRA decreased further over time. Increased UVs were found for CR and CRA. For CR and CRA, there was no significant difference in UV at the end of the experiment from the initial value before erosion. In the results of SEM observation, the CR and CRA groups had similar morphologic features in that etching patterns were not clearly due to precipitation between the enamel rods. From the results of this in vitro study, it might be concluded that applying enamel matrix derivatives and self-assembling peptides on erosive lesions can improve remineralization.