So far, the combination of methylammonium bromide/methylammonium chloride (MABr/MACl) or methylammonium iodide (MAI)/MACl is the most frequently used additives to stabilize formamidinium lead iodide (FAPbI3) fabricated by the sequential deposition method. However, the enlarged bandgap due to the addition of bromide and the ambiguous functions of these additives in lead iodide (PbI2) transformation are still worth considering. Herein, the roles of MACl in sequentially deposited Br‐free FA‐based perovskites are systematically investigated. It is found that MACl can finely regulate the PbI2/FAI reaction, tune the phase transition at room temperature, and adjust intermediate‐related perovskite crystallization and decomposition during thermal annealing. Compared to FAPbI3, the perovskite with MACl exhibits larger grain, longer carrier lifetime, and reduced trap density. The resultant solar cell therefore achieves a champion power conversion efficiency (PCE) of 23.1% under reverse scan with a stabilized power output of 23.0%. In addition, it shows much improved photostability under 100 mW cm−2 white illumination (xenon lamp) in nitrogen atmosphere without encapsulation.

Rapid detection and differentiation of methicillin-resistant Staphylococcus aureus (MRSA) is critical for the early diagnosis of difficult-to-treat nosocomial and community acquired clinical infections and improved epidemiological surveillance. We developed a microfluidics chip coupled with surface enhanced Raman scattering (SERS) spectroscopy (532 nm) “lab-on-a-chip” system to rapidly detect and differentiate methicillin-sensitive S. aureus (MSSA) and MRSA using clinical isolates from China and the United States. A total of 21 MSSA isolates and 37 MRSA isolates recovered from infected humans were first analyzed by using polymerase chain reaction (PCR) and multilocus sequence typing (MLST). The mecA gene, which refers resistant to methicillin, was detected in all the MRSA isolates and different allelic profiles were identified assigning isolates as either previously identified or novel clones. A total of 17,400 SERS spectra of the 58 S. aureus isolates were collected within 3.5 hours using this optofluidic platform. Intra- and inter-laboratory spectral reproducibility yielded a differentiation index value of 3.43 to 4.06 and demonstrated the feasibility of using this optofluidic system at different laboratories for bacterial identification. A global SERS-based dendrogram model for MRSA and MSSA identification and differentiation to the strain level was established and cross-validated (Simpson index of diversity of 0.989) and had an average recognition rate of 95% for S. aureus isolates associated with a recent outbreak in China. SERS typing correlated well with MLST indicating that it has high sensitivity and selectivity and would be suitable for determining the origin and possible spread of MRSA. A SERS-based partial least-squares regression model could quantify the actual concentration of a specific MRSA isolate in a bacterial mixture at levels from 5 to 100% (regression coefficient, > 0.98; residual prediction deviation, >10.05). This optofluidic platform has advantages over traditional genotyping for ultrafast, automated and reliable detection and epidemiological surveillance of bacterial infections.

Friction is a major inhibitor in almost every mechanical system. Enlightened by the Leidenfrost effect – a droplet can be levitated by its own vapor layer on a sufficiently hot surface – we demonstrate for the first time that a small cart can also be levitated by Leidenfrost vapor. The levitated cart can carry certain amount of load and move frictionlessly over the hot surface. The maximum load that the cart can carry is experimentally tested over a range of surface temperatures. We show that the levitated cart can be propelled not only by gravitational force over a slanted flat surface, but also self-propelled over a ratchet shaped horizontal surface. In the end, we experimentally tested water consumption rate for sustaining the levitated cart, and compared the results to theoretical calculations. If perfected, this frictionless Leidenfrost cart could be used in numerous engineering applications where relative motion exists between surfaces.

Wide-band gap (WBG) mixed-halide perovskites have drawn much attention because of their excellent optoelectronic properties and the potential to be deployed in tandem solar cells. Nevertheless, the bromine incorporation inevitably leads to photoinduced phase segregation in WBG mixed-halide perovskites. Herein, potassium is used to effectively suppress photoinduced phase segregation, which is visualized with confocal photoluminescence microscopy imaging. Strikingly, the potassium passivation not only inhibits the formation of the narrow-band gap subphase but also enhances the crystallinity of the WBG mixed-halide perovskite. In addition, the potassium-passivated WBG perovskite exhibits lower defect density, longer charge carrier lifetime, and better photostability. As a result, the optimized KI (2 mol %)-passivated WBG perovskite solar cells (PSCs) deliver a champion power conversion efficiency of 18.3% with negligible hysteresis. They maintain 98% of their initial efficiency after 400 h under 100 mW•cm −2 white light illumination in nitrogen.

Radiation crosslinked ultra high molecular weight polyethylene (UHMWPE) with high mechanical strength, wear resistance, and oxidative stability is critical for the long term performance and life span of the joint implants based on crosslinked UHMWPE. The use of antioxidants and/or radical scavengers has proven efficient in stabilising crosslinked UHMWPE against oxidation, whereas challenges remain to explore new methods to offer not only oxidative stability, but also superior wear resistance and mechanical properties in the long term. Herein, two natural polyphenols, gallic acid (GA) and dodecyl gallate (DG), containing three hydroxy groups each, have been demonstrated potent in protecting irradiated UHMWPE against adverse oxidative challenging at elevated temperatures. The presence of these polyphenols does not inhibit the crosslinking in comparison to the high dose-irradiated vitamin E/UHMWPE. The tensile and impact properties of these polyphenol-stabilized highly cross-linked UHMWPE after accelerated ageing in accordance with ASTM F2003 are superior to those of the irradiated and remelted UHMWPE. Pin-on-disc (POD) wear tests of these materials demonstrated low wear compared to that of highly crosslinked and remelted UHMWPE. In vitro culture with chondrocytes showed a slightly improved biocompatibility for these irradiated antioxidant/UHMWPE. These natural polyphenols are potential alternatives for the stabilisation of highly crosslinked UHMWPE for joint arthroplasty.