Four aluminum surfaces with wettability varied from superhydrophilic to superhydrophobic were prepared by combining an etching and a coating process. The surface wettability was checked in terms of water contact angle (CA) and sliding angle (SA) under different humidity at -10 °C. High-speed photography was applied to study water droplet impact dynamics on these surfaces. It was found that single and successive water droplets could rebound on the superhydrophobic surface and roll off at a tilt angle larger than 30° under an extremely condensing weather condition (-10 °C and relative humidity of 85-90%). In addition, the superhydrophobic surface showed a strong icephobic property, the ice adhesion on this surface was only 13% of that on the superhydrophilic surface, though they had a similar nano/microtopological structure. Moreover, this superhydrophobic surface displayed an excellent durability of the icephobic property. The ice adhesion only increased to 20% and 16% of that on the superhydrophobic surface after the surface was undergone 20 icing/ice-breaking cycles and 40 icing/ice-melting cycles, respectively. Surface profile and XPS studies on these surfaces indicated a minor damage of the surface nano/microstructure and the coating layer upon these multiple ice-breaking and ice-melting processes. Therefore, this superhydrophobic surface could be a good candidate for icephobic applications.

A simple and low-cost technique for the preparation of silicon-oil-infused polydimethylsiloxane (PDMS) coatings with different silicon oil contents have been developed and studied. This material is designed for ice-phobic applications, and thus a high hydrophobic property of PDMS is maintained by avoiding any polar groups such as C═O and OH in the structure. Therefore, the polymer main chain was attached with vinyl and Si-H groups to obtain a cross-linking capability, meanwhile to ensure a nonpolar chemical structure. Its ice-phobic property has been investigated in terms of ice adhesion strength (tensile and shear), water contact angle, icing dynamics using high-speed photography and morphology using TEM, SEM and AFM. The prepared coating surface shows a low surface energy and very low ice adhesion strength of 50 kPa, only about 3% of the value on a bare aluminum (Al) surface. In the silicon oil infused PDMS coatings, the low surface energy of the silicon oil and PDMS, and the high mobility of silicon oil played an important role on the ice-phobic property. Both of these factors offer the surface a large water contact angle and hence a small contact area, leading to the formation of a loose ice layer. In addition, the oil infused polymer structure significantly reduces the contact area of the ice with solid substrate since the ice mostly contacts with the mobile oil. This leads to a very weak interaction between the substrate and ice, consequently significantly reduces the ice adhesion strength on the surface. Therefore, such material could be a good candidate for ice-phobic coatings on which the accumulated ice may be easily removed by a nature force, such as wind, gravity, and vibration.

The effective activation and utilization of metakaolin as an alkali activated geopolymer precursor and its use in concrete surface protection is of great interest. In this paper, the formula of alkali activated metakaolin-based geopolymers was studied using an orthogonal experimental design. It was found that the optimal geopolymer was prepared with metakaolin, sodium hydroxide, sodium silicate and water, with the molar ratio of SiO2:Al2O3:Na2O:NaOH:H2O being 3.4:1.1:0.5:1.0:11.8. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) were adopted to investigate the influence of curing conditions on the mechanical properties and microstructures of the geopolymers. The best curing condition was 60 °C for 168 h, and this alkali activated metakaolin-based geopolymer showed the highest compression strength at 52.26 MPa. In addition, hollow micro-sphere glass beads were mixed with metakaolin particles to improve the thermal insulation properties of the alkali activated metakaolin-based geopolymer. These results suggest that a suitable volume ratio of metakaolin to hollow micro-sphere glass beads in alkali activated metakaolin-based geopolymers was 6:1, which achieved a thermal conductivity of 0.37 W/mK and compressive strength of 50 MPa. By adjusting to a milder curing condition, as-prepared alkali activated metakaolin-based geopolymers could find widespread applications in concrete thermal protection.

The surfaces of nanotube arrays were coated with poly(methyl methacrylate) (PMMA) using an imprinting method with an anodized alumina membrane as the template. The prepared nanotube array surfaces then either remained untreated or were coated with NH2(CH2)3Si(OCH3)3(PDNS) or CF3(CF2)7CH2CH2Si(OC2H5)3 (PFO). Thus, nanotube arrays with three different surfaces, PDNS, PMMA (without coating), and PFO, were obtained. All three surfaces (PDNS, PMMA, and PFO) exhibited superhydrophobic properties with contact angles (CA) of 155, 166, and 168°, respectively, and their intrinsic water contact angles were 30, 79, and 118°, respectively. The superhydrophobic stabilities of these three surfaces were examined under dynamic impact and static pressures in terms of the transition from the Cassie-Baxter mode to the Wenzel mode. This transition was determined by the maximum pressure (p(max)), which is dependent on the intrinsic contact angle and the nanotube density of the surface. A p(max) greater than 10 kPa, which is sufficiently large to maintain stable superhydrophobicity under extreme weather conditions, such as in heavy rain, was expected from the PFO surface. Interestingly, the PDNS surface, with an intrinsic CA of only 30°, also displayed superhydrophobicity, with a CA of 155°. This property was partially maintained under the dynamic impact and static pressure tests. However, under an extremely high pressure (0.5 MPa), all three surfaces transitioned from the Cassie-Baxter mode to the Wenzel mode. Furthermore, the lost superhydrophobicity could not be recovered by simply relieving the pressure. This result indicates that the best way to maintain superhydrophobicity is to increase the p(max) of the surface to a value higher than the applied external pressure by using low surface energy materials and having high-density binary nano-/microstructures on the surface.

No abstract

Platelet-activating factor (PAF) is a bioactive lipid mediator which serves as a reciprocal messenger between the immune and nervous systems. PAF, a pluripotent inflammatory mediator, is extensively expressed in many cells and tissues and has either beneficial or detrimental effects on the progress of inflammation-related neuropathology. Its wide distribution and various biological functions initiate a cascade of physiological or pathophysiological responses during development or diseases. Current evidence indicates that excess PAF accumulation in CNS diseases exacerbates the inflammatory response and pathological consequences, while application of PAF inhibitors or PAFR antagonists by blocking this signaling pathway significantly reduces inflammation, protects cells, and improves the recovery of neural functions. In this review, we integrate the current findings of PAF signaling in CNS diseases and elucidate topics less appreciated but important on the role of PAF signaling in neurological diseases. We propose that the precise use of PAF inhibitors or PAFR antagonists that target the specific neural cells during the appropriate temporal window may constitute a potential therapy for CNS diseases.

Rationale: Wandering spleen (WS) is a rare clinical entity characterized by splenic hypermobility caused by absent or abnormal laxity of the suspensory ligaments, which fix the spleen in its normal position. Due to abnormal attachment, the spleen is predisposed to torsion and a series of complications. Pediatric WS is mostly reported in children aged <10 years, especially among infants aged <1 year; it is uncommon among toddlers between 1 and 3 years. To the authors’ knowledge, only seven cases of WS have been described previously. Herein, we present the case of a 3-year-old toddler with WS and splenic torsion. Patient concerns: A 3-year-old boy was presented to the pediatric emergency room with a 2-day history of abdominal pain and vomiting. The ultrasonographic examination revealed a mass in the left upper abdomen cavity and absence of spleen in its normal position. Computed tomography showed an enlarged displaced spleen occupying the left abdomen cavity with an elongated splenic vascular pedicle (whirl sign), suggesting splenic torsion. Diagnoses: The patient was diagnosed that had WS and splenomegaly, with or without complications due to splenic torsion. Interventions: The patient underwent emergency laparotomy and splenectomy due to nonviability after detorsion. Outcomes: The postoperative course was uneventful, and the patient was discharged on the 7th day postoperatively without complications. The patient had favorable outcome over a 1-year follow-up. Lessons: Herein, we reported the case of a toddler with WS with splenic torsion. Moreover, after reviewing relevant studies in literature, we presented our findings on the diagnosis and treatment of toddlers with WS. Toddlers with WS are characterized by acute abdominal pain, unclear history description, examination restrictions, and high rates of life-threatening complications. High level of suspicion, careful physical examination, detailed history collection, and objective investigation are crucial in the management of toddlers with WS.

A novel soft-template (ST) is fabricated and successfully employed as mesoporogen to synthesis hierarchical ZSM-5 zeolites with outstanding mesoporosity and high hierarchy factors. The as-produced soft-template can connect steadily with the MFI frameworks by covalent bonds of –Si–O–Si– during the high-temperature hydrothermal crystallization process. This type of connection mode can effectively avoid the formation of amorphous materials, and the specific structure of this soft-template can efficiently introduce plentiful of mesopores with few micropores being consumed. The particles of as-synthesized hierarchical ZSM-5 zeolites are in size of about 1 μm, which are made up of nanocrystals of 60–150 nm. The structure parameters of these samples are characterized with the techniques of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, nitrogen sorption, scanning electron microscope (SEM), transmission electron microscope (TEM), NH3 temperature-programmed desorption (NH3-TPD) and thermogravimetric (TG). Due to the nature of zeolites and great microporosity, these hierarchical samples present great tolerance of hydrothermal treatment. And because of the intracrystalline mesopores, large external surface areas, and abundant accessible acid sites, whether in conversion rate of reactants or selectivity of products, the hierarchical samples exhibit excellent catalytic performance in the reactions of alkylation between benzene and benzyl alcohol, cracking of 1,3,5-tri-isopropylbenzene, and thermal cracking of low-density polyethylene (LDPE), respectively.Electronic supplementary materialThe online version of this article (10.1186/s11671-018-2779-8) contains supplementary material, which is available to authorized users.