Benzo(a)pyrene, as the main polycyclic aromatic hydrocarbon pollutant in marine oil spill pollution, has negative effects on marine ecology and human health. A facile and sensitive method of rapid benzo(a)pyrene detection in seawater is essential for marine conservation. In this paper, a novel immunosensor is fabricated using a multi-walled carbon nanotubes-chitosan composite loaded with benzo(a)pyrene antibody. This immunosensor is based on a biosensing assay mechanism that uses multi-walled carbon nanotubes-chitosan composites as conductive mediators to enhance electron transfer kinetics. Then, potassium ferricyanide was used as an electrochemical probe to produce an electrochemical signal for the voltammetric behavior investigation of the immune response by differential pulse voltammetry. Under optimal experimental conditions, the peak current change was inversely proportional to the benzo(a)pyrene concentration in the range of 0.5 ng⋅ml−1 and 80 ng⋅ml−1 with a detection limit of 0.27 ng⋅ml−1. The immunosensor was successfully applied to assay BaP in seawater, and the recovery was between 96.6 and 100%, which exhibited a novel, sensitive and interference-resistant analytical method for real-time water environment monitoring. The results demonstrate that the proposed immunosensor has a great potential for application in the monitoring of seawater.

<abstract><p>Unlike conventional methods of pests control, introducing in an appropriate mathematical model can contribute a batter performance on pests control with higher efficiency while lest damage to ecosystem. To fill the research gap on plant root pest control, we propose a plant root pest management model with state pulse feedback control. Firstly, the stability of the equilibrium point of the model (1.3) is analyzed by using the linear approximate equation, given that the only positive equilibrium point of model (1.3) is globally asymptotically stable. Moreover, the existence and uniqueness of order 1 periodic solutions of model (1.3) are discussed in detail according to the geometric theory of semi-continuous dynamical systems, successor functions method and the qualitative theory of differential equations. Finally, with further analysis in different methods, the asymptotic stability of the order 1 periodic solution of model (1.3) is obtained by using Similar Poincare Criterion or interval set theorem. The results show that this model can effectively control the number of pests below the economic level of damage.</p></abstract>

Phenanthrene (PHE), as a structurally simple, tricyclic, polycyclic aromatic hydrocarbon (PAHs), is widely present in marine environments and organisms, with serious ecological and health impacts. It is crucial to study fast and simple high-sensitivity detection methods for phenanthrene in seawater for the environment and the human body. In this paper, a immunosensor was prepared by using a multi-wall carbon nanotube (MWCNTs)-chitosan oligosaccharide (COS) nanocomposite membrane loaded with phenanthrene antibody. The principle was based on the antibody–antigen reaction in the immune reaction, using the strong electron transfer ability of multi-walled carbon nanotubes, coupled with chitosan oligosaccharides with an excellent film formation and biocompatibility, to amplify the detection signal. The content of the phenanthrene in seawater was studied via differential pulse voltammetry (DPV) using a potassium ferricyanide system as a redox probe. The antibody concentration, pH value, and probe concentration were optimized. Under the optimal experimental conditions, the response peak current of the phenanthrene was inversely proportional to the concentration of phenanthrene, in the range from 0.5 ng·mL−1 to 80 ng·mL−1, and the detection limit was 0.30 ng·mL−1. The immune sensor was successfully applied to the detection of phenanthrene in marine water, with a recovery rate of 96.1~101.5%, and provided a stable, sensitive, and accurate method for the real-time monitoring of marine environments.

This research proposes a seawater desalination system driven by photovoltaic and solar thermal energy for remote regions such as islands and seaside villages where fresh water is not accessible. The performance of this system is demonstrated through experiments, and the main concerns are the output of the photovoltaic power generation system, power quantity, water yield, and the loads under different solar irradiance and temperature. In this system, a PLC is used as the controller to adjust the water pump by the collection and processing of sensor data. A load switching time system is designed to select different operating schemes under different environments in order to save energy. The control method of this system is developed to ensure that the photovoltaic power generation system does not undervoltage while maintaining the normal operation of the desalination system. An improved Perturbation and Observation (P&O) algorithm is also proposed as a new Maximum Point Power Tracking (MPPT) method to solve the problem of misjudgment and oscillation after tracking the maximum power point (MPP) in the traditional P&O algorithm. The simulation test in the MATLAB/Simulink environment shows that when external irradiance changes, the improved P&O algorithm can track the MPP faster than the traditional P&O algorithm, and the amplitude of oscillation on the MPP is smaller. The hardware experiments show that this system can operate stably and flexibly, and it is capable of producing 5.18 kWh of electric energy and 335.81 kg of freshwater per day. The maximum yield of the unit can reach 565.75 kg per day and the maximum daily power generation is 8.12 kWh.

It is necessary to detect cadmium ions in seawater with high sensitivity because the pollution of cadmium ions seriously endangers the health and life of human beings. Nano-Fe3O4/MoS2/Nafion modified glassy carbon electrode was prepared by a drop coating method. The electrocatalytic properties of Nano-Fe3O4/MoS2/Nafion were measured by Cyclic Voltammetry (CV). Differential Pulse Voltammetry (DPV) was used to study the stripping Voltammetry response of the modified electrode to Cd2+. The optimal conditions were determined: In 0.1 mol/L HAc-NaAc solution, the solution pH was 4.2, the deposition potential was − 1.0 V, and the deposition time was 720 s, the membrane thickness was 8 μL. Under the optimum condition, the linear relation of Cd2+ concentration was found in the range of 5–300 μg/L, and the detection limit was 0.053 μg/L. The recovery of Cd2+ in seawater ranged from 99.2 to 102.9%. A composite material with simple operation, rapid response and high sensitivity was constructed for the determination of Cd2+ in seawater. Graphical abstract

Unlike conventional lead ion (Pb2+) detecting methods, electrochemical methods have the attractive advantages of rapid response, good portability and high sensitivity. In this paper, a planar disk electrode modified by multiwalled carbon nanotube (MWCNTs)/chitosan (CS)/lead (Pb2+) ionophore IV nanomaterial and its matched system are proposed. This system presented a good linear relationship between the concentration of Pb2+ ions and the peak current in differential pulse stripping voltammetry (DPSV), under optimized conditions of −0.8 V deposition potential, 5.5 pH value, 240 s deposition time, performed sensitive detection of Pb2+ within sensitivity of 1.811 μA · μg−1 and detection limit of 0.08 μg · L−1. Meanwhile, the results of the system in detecting lead ions in real seawater samples are highly similar to that of inductively coupled plasma emission spectrometer (ICP-MS), which proved a practicability for the system in detection of trace-level Pb2+.