Polishing the surface is recommended for a full-contour zirconia restoration because polished zirconia presents favorable wear behavior opposing natural teeth.

Objective: To use a systematic review to determine which materials and technique/protocol present the highest success rate in bonding brackets to porcelain surfaces. Materials and Methods: Different databases were searched without limitations up to July 2013. Additionally, the bibliographies of the finally selected articles were hand searched to identify any relevant publications that were not identified earlier. In vitro and in vivo articles were included. Results: No in vivo articles were found that fulfilled the inclusion criteria. A total of 45 in vitro articles met all inclusion criteria. They were published between 2000 to July 2013. Conclusions: The best protocol described in this review is the etching of 9.6% hydrofluoric acid for 1 minute, rinsed for 30 seconds, and then air-dried. The etching of hydrofluoric acid should be followed by an application of silane. Considering the harmful effects of etching with hydrofluoric acid, another appropriate suggestion is mechanical roughening with sandblasting followed by an application of silane. (Angle Orthod. 2014;84:555-560.)

PURPOSEVinyl polyether silicone (VPES) has a different composition from other elastomeric impression materials as it combines vinyl polysiloxane (VPS) and polyether (PE). Therefore, it is important to study its properties and behavior under different test conditions. This study investigated the dimensional stability of 5 VPES consistencies when stored for up to 2 weeks, with and without using a standard disinfection procedure.MATERIALS AND METHODS40 discs of each VPES consistency (total 200) were made using a stainless steel die and ring as described by ANSI /ADA specification No. 19. 20 discs of each material were immersed in a 2.5% buffered glutaraldehyde solution for 30 minutes. Dimensional stability measurements were calculated immediately after fabrication and repeated on the same discs after 7 and 14 days of storage. The data was analyzed using two-way ANOVA with a significance level set at α = 0.05.RESULTSThe discs mean contraction was below 0.5% at all test times ranging from 0.200 ± 0.014 to 0.325 ± 0.007. Repeated measures ANOVA showed a statistically significant difference after 2-week storage between the disinfected and non-disinfected groups (P < .001). Although there was no statistically significant difference between the materials at the time of fabrication, the contraction of the materials increased with storage for 1 and 2 weeks.CONCLUSIONThe dimensional changes of VPES impression discs after disinfection and prolonged storage complied with ANSI/ADA standard. The tested VPES impression materials were dimensionally stable for clinical use after disinfection for 30 minutes in glutaraldehyde and storage for up to 2 weeks.

The aims of this study were twofold: to compare the static compressive strength at the implant-abutment interface of 3 design systems and to describe the implant abutment connection failure mode. A stainless steel holding device was designed to align the implants at 30 degrees with respect to the y-axis. Sixty-nine specimens were used, 23 for each system. A computer-controlled universal testing machine (MTS 810) applied static compression loading by a unidirectional vertical piston until failure. Specimens were evaluated macroscopically for longitudinal displacement, abutment looseness, and screw and implant fracture. Data were analyzed by analysis of variance (ANOVA). The mean compressive strength for the Unipost system was 392.5 psi (SD +/-40.9), for the Spline system 342.8 psi (SD+/-25.8), and for the Screw-Vent system 269.1 psi (SD+/-30.7). The Unipost implant-abutment connection demonstrated a statistically significant superior mechanical stability (P < or = .009) compared with the Spline implant system. The Spline implant system showed a statistically significant higher compressive strength than the Screw-Vent implant system (P < or =.009). Regarding failure mode, the Unipost system consistently broke at the same site, while the other systems failed at different points of the connection. The Unipost system demonstrated excellent fracture resistance to compressive forces; this resistance may be attributed primarily to the diameter of the abutment screw and the 2.5 mm counter bore, representing the same and a unique piece of the implant. The Unipost implant system demonstrated a statistically significant superior compressive strength value compared with the Spline and Screw-Vent systems, at a 30 degrees angulation.

Purpose The aim of this study was to evaluate the influence of multimode MDP-based primers and different application protocols on the bond strength of a representative resin cement to an yttrium stabilized tetragonal zirconia (Y-TZP) ceramic. Materials and Methods The occlusal dentin from 60 human molars was exposed. The teeth and zirconia cylinders (N = 60) (3 mm of diameter; 4 mm of height) were divided into six groups (n = 10) according to the ceramic surface conditioning: (1) air abraded with SiO2 particles; (2) Z-Prime Plus; (3) air abraded with SiO2 particles + Z-Prime Plus; (4) air abraded with SiO2 particles + All-Bond Universal; (5) air abraded with SiO2 particles + ScotchBond Universal Adhesive; and (6) untreated zirconia. The luting agent (Duo-Link cement) was applied on the treated dentin surface. Specimens were stored in water (37°C, 24 h) and tested in shear bond strength. Data were statistically analyzed using 2-way ANOVA and Post hoc Tukey tests (α = 0.05). Results Significant effects of ceramic conditioning were found (p < 0.0001). The specimens sandblasted with silica particles followed by the application of Z-Prime Plus or All-Bond Universal presented greater bond strength values. For the untreated zirconia, several specimens failed prematurely prior to testing. Conclusions Sandblasting with silica particles combined with Z-Prime Plus increased the bond strength.

Minimal tooth reduction is crucial for the long-term success of adhesive restorations. It has been proven that bonding to enamel is more predictable in obtaining better long-term success than dentin due to its higher percentage of mineral content. The diagnostic wax-up and subsequent mock-up are the first diagnostic tools available to evaluate discrepancies between current and ideal tooth proportions. The intraoral mock-up provides the patient a tactile and visual evaluation of the size, shape, and shade of the proposed final restorations, and at the same time, the clinician can evaluate the smile line, lip support, phonetics, and occlusion. During the tooth preparation, the mock-up provides a reduction guide to the clinician to achieve the minimal required reduction for the final restoration avoiding the over-reduction and dentin exposure. This clinical report shows feldspathic veneer restorations provided with conservative tooth preparation. The long-term success of the restoration requires following well-defined protocols for restorative material selection, conservative tooth preparation, total isolation with rubber dam, and bonding ceramic protocols.

The reported clinical scenarios presented two patients, one managed with a prefabricated abutment and the other with a customized abutment, and both patients were pleased with the outcome. However, from a professional viewpoint, the esthetic outcome using the custom zirconia abutment was superior to that using the prefabricated titanium abutment.

No abstract