The surface chemistry of materials has an interactive influence on cell behavior. The optimal adhesion of mammalian cells is critical in determining the cell viability and proliferation on substrate surfaces. Because of the inherent high hydrophobicity of a poly(dimethylsiloxane) (PDMS) surface, cell culture on these surfaces is unfavorable, causing cells to eventually dislodge from the surface. Although physically adsorbed matrix proteins can promote initial cell adhesion, this effect is usually short-lived. Here, (3-aminopropyl)triethoxy silane (APTES) and cross-linker glutaraldehyde (GA) chemistry was employed to immobilize either fibronectin (FN) or collagen type 1 (C1) on PDMS. The efficiency of these surfaces to support the adhesion and viability of mesenchymal stem cells (MSCs) was analyzed. The hydrophobicity of the native PDMS decreased significantly with the mentioned surface functionalization. The adhesion of MSCs was mostly favorable on chemically modified PDMS surfaces with APTES + GA + protein. Additionally, the spreading area of MSCs was significantly higher on APTES + GA + C1 surfaces than on other unmodified/modified PDMS surfaces with C1 adsorption. However, there were no significant differences in the MSC spreading area on the unmodified/modified PDMS surfaces with FN adsorption. Furthermore, there was a significant increase in cell proliferation on the PDMS surface with APTES + GA + protein functionalization as compared to the PDMS surface with protein adsorption only. Therefore, the covalent surface chemical modification of PDMS with APTES + GA + protein could offer a more biocompatible platform for the enhanced adhesion and proliferation of MSCs. Similar strategies can be applied for other substrates and cell lines by appropriate combinations of self-assembly monolayers (SAMs) and extracellular matrix proteins.

Polydimethylsiloxane (PDMS) has been extensively exploited to study stem cell physiology in the field of mechanobiology and microfluidic chips due to their transparency, low cost and ease of fabrication. However, its intrinsic high hydrophobicity renders a surface incompatible for prolonged cell adhesion and proliferation. Plasma-treated or protein-coated PDMS shows some improvement but these strategies are often short-lived with either cell aggregates formation or cell sheet dissociation. Recently, chemical functionalization of PDMS surfaces has proved to be able to stabilize long-term culture but the chemicals and procedures involved are not user- and eco-friendly. Herein, we aim to tailor greener and biocompatible PDMS surfaces by developing a one-step bio-inspired polydopamine coating strategy to stabilize long-term bone marrow stromal cell culture on PDMS substrates. Characterization of the polydopamine-coated PDMS surfaces has revealed changes in surface wettability and presence of hydroxyl and secondary amines as compared to uncoated surfaces. These changes in PDMS surface profile contribute to the stability in BMSCs adhesion, proliferation and multipotency. This simple methodology can significantly enhance the biocompatibility of PDMS-based microfluidic devices for long-term cell analysis or mechanobiological studies.

No abstract

No abstract

In recent years, poly(dimethylsiloxane) (PDMS)-based microfluidic devices have become very popular for on-chip cell investigation. Maintenance of mammalian cell adhesion on the substrate surface is crucial in determining the cell viability, proliferation and differentiation. However, the inherent hydrophobicity of PDMS is unfavourable for cell culture, causing cells to eventually dislodge from the surface. Although physically adsorbed matrix proteins can promote initial cell adhesion, this effect is usually short-lived. To address this critical issue, in this study, we employed (3-aminopropyl) triethoxy silane (APTES) and cross-linker glutaraldehyde (GA) chemistry to immobilize collagen type 1 (Col1) on PDMS. These modified surfaces are highly efficient to support the adhesion of mesenchymal stem cells (MSCs) with no deterioration of their potency. Significant changes of the native PDMS surface properties were observed with the proposed surface functionalization, and MSC adhesion was improved on PDMS surfaces modified with APTES + GA + Protein. Therefore, this covalent surface modification could generate a more biocompatible platform for stabilized cell adhesion. Furthermore, this modification method facilitated long-term cell attachment, which is favourable for successful induction of osteogenesis and cell sheet formation with an increased expression of osteogenic biomarkers and comparable extracellular matrix (ECM) constituent biomarkers, respectively. The surface silanization can be applied to PDMS-based microfluidic systems for long-term study of cellular development. Similar strategies could also be applied to several other substrate materials by appropriate combinations of self-assembled monolayers (SAMs) and ECM proteins.

No abstract

No abstract

Inspired by the paper platforms for 3-D cell culture, a paper-based microfluidic device containing drug concentration gradient was designed and constructed for investigating cell response to drugs based on high throughput analysis. This drug gradient generator was applied to generate concentration gradients of doxorubicin (DOX) as the model drug. HeLa cells encapsulated in collagen hydrogel were incubated in the device reservoirs to evaluate the cell viability based on the controlled release of DOX spatially. It was demonstrated that drug diffusion through the paper fibers created a gradient of drug concentration, which influenced cell viability. This drug screening platform has a great opportunity to be applied for drug discovery and diagnostic studies with simultaneous and parallel tests of drugs under various gradient concentrations.