No abstract

No abstract

Thermal conductivity was dramatically increased after adding natural fiber into hexagonal boron nitride (hBN)/epoxy composites. Although natural fiber does not show high-thermal conductivity itself, this study found that the synergy of natural fiber with hBN could significantly improve thermal conductivity, compared with that solely using hBN. A design of mixtures approach using constant fibers with increasing volume fractions of hBN was examined and compared. The thermal conductivity of the composite containing 43.6% hBN, 26.3% kenaf fiber and 30.1% epoxy reached 6.418 W m−1 K−1, which was 72.3% higher than that (3.600 W m−1 K−1) of the 69.0% hBN and 31.0% epoxy composite. Using the scanning electron microscope (SEM) and micro computed tomography (micro-CT), it was observed that the hBN powders were well distributed and ordered on the fiber surfaces enhancing the ceramic filler’s interconnection, which may be the reason for the increase in thermal conductivity. Additionally, the results from mechanical and dynamic mechanical tests showed that performances dramatically improved after adding kenaf fibers into the hBN/epoxy composite, potentially benefiting the composite’s use as an engineered material.

No abstract

As a hydrophilic material, wood is difficult to utilize for external applications due to the variable weather conditions. In this study, an efficient, facile, and low-cost method was developed to enhance the hydrophobicity of wood. By applying the low-temperature chemical vapor deposition (CVD) technology, the polydimethylsiloxane-coated wood (PDMS@wood) with hydrophobic surface was fabricated employing dichlorodimethylsilane as the CVD chemical resource. The result of water contact angle (i.e., 157.3°) revealed the hydrophobic behavior of the PDMS@wood. The microstructures of the wood samples were observed by scanning electron microscopy and energy dispersive X-ray spectroscopy (EDS) analysis verified PDMS successfully coated on wood surfaces. The chemical functional groups of the PDMS@wood were investigated by Fourier transform infrared (FT-IR) and Raman spectra. The thermogravimetric results indicated the enhanced thermal stability of the wood after PDMS coating. In addition, the stability test of PDMS@wood indicated that the hydrophobicity properties of the PDMS@wood samples were preserved after long-time storage (e.g., 30 days). The scratch test was carried out to examine the abrasion resistance of the hydrophobic coatings on PDMS@wood surface. It was suggested that low-temperature CVD process could be a successful approach for fabricating hydrophobic wood.

Chrysotile nanotubes (ChNTs) were synthesized under hydrothermal conditions. These synthetic nanotubes crystallographically and morphologically mimic the nanofibrils of natural white asbestos but they are considerably shorter. ChNTs containing polyimide nanocomposites were prepared by a solution mixing/casting method. Oxygen and water vapor barrier of the nanocomposite films were tested and related to the amount, dispersion, and orientation of the nanotubes. The dispersion and orientation of the nanotubes were examined by transmission electron microscopy (TEM). The nanotubes were nanodispersed and oriented in the plane of the film in the nanocomposites with up to 4.5% (vol/vol) of ChNTs leading to a gradual increase of the gas barrier. The lowest gas permeability was 60% smaller than that for the pristine polyimide film. However, with the onset of nanotube micro aggregation at larger ChNTs loadings the nanotube dispersion and orientation were compromised and oxygen barrier was reduced. The efficacy of nanotubes to enhance polymer gas barrier was discussed and compared with that by nanoplatelets. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1184–1193

No abstract

The kenaf fiber/polyester composites, owning the comparable mechanical properties with commercial glass-fiber sheet molding compounds (SMC) for automotive application, were achieved through the high pressure-assisted magnesium carbonate impregnated fibers and the vacuum-assisted resin transfer molding process. The in situ inorganic nanoparticle impregnation (INI) process was performed by immersing the alkali retted fibers into magnesium chloride solution with various pressures and then treated by sodium carbonate to yield the INI-treated fibers. The magnesium carbonate content was increased by 180.3%, when a 13.79 MPa pressure was applied during the magnesium carbonate immersing process, resulting in lower porosity of fibers. Compared to the untreated fiber/polyester composite, the mechanical properties of the high pressure-assisted INI-treated fiber/polyester composites were enhanced by 18.6-277.3%, and the 24-hour thickness swelling and water absorption were reduced by 64.4% and 62.2%, respectively. The mechanical properties and specific mechanical properties were comparable with or excessed to that of glass-fiber SMC.