Formamidinium lead trihalide perovskite (FAPbI3) was successfully introduced into hole-conductor-free, fully printable mesoscopic perovskite solar cells with a carbon counter electrode.

Ultrasmall black phosphorus quantum dots (BPQDs) serve as the near-infrared light absorber and charge transfer layer in the photocathode of a bifacial n-type dye sensitized solar cell. Wideband light absorption and ≈20% enhancement in the light-to-electron efficiency are accomplished due to the fast carrier transfer and complementary light absorption by the BPQDs demonstrating that BP has large potential in photovoltaics.

The effect of lithium iodide concentration on the conduction behavior of poly(ethylene oxide)-poly(vinylidene fluoride) (PEO-PVDF) polymer-blend electrolyte and the corresponding performance of the dye-sensitized solar cell (DSSC) were studied. The conduction behavior of these electrolytes was investigated with varying LiI concentration (10-60 wt % in polymer blend) by impedance spectroscopy. A "polymer-in-salt" like conduction behavior has been observed in the high salt concentration region. The transition from "salt-in-polymer" to "polymer-in-salt" conduction behavior happened at the salt content of 23.4 wt %, which is much lower than 50 wt % as generally reported. The electrolyte shows the highest ionic conductivity (approximately 10(-3) S cm(-1)) at the salt concentration above 23.4 wt %. From the evaluation of salt effect on the performances of corresponding DSSC, we find that increasing LiI concentration leads to increased short-circuit photocurrent density (Jsc) caused by enhanced I3(-) diffusion up to an LiI content of 28.9 wt %. Above this limitation, the Jsc decreases as a result of increased charge recombination caused by the further increased I3(-) concentration. The open-circuit voltage (Voc) increases gradually with LiI concentration owing to the enhanced I(-) content in DSSC. The optimized conversion efficiency is obtained at a salt content of 28.9 wt % in the "polymer-in-salt" region, with high ionic conductivity (1.06 x 10(-3) S cm(-1)). Based on these facts, we suggest that the changes of conduction behavior and the changes of I3(-) and I(-) concentrations in the electrolytes contribute to the final performance variation of the corresponding DSSC with varying LiI concentration.

The objectives of this study are to prepare sulfhydryl-modified Fe3O4@SiO2 core/shell magnetic nanocomposites, assess their toxicity in vitro, and explore their potential application in the biomedical fields. Fe3O4 nanoparticles synthesized by facile solvothermal method were coated with SiO2 via the Stöber method and further modified by the meso-2,3-dimercaptosuccinic acid (DMSA) to prepare Fe3O4@SiO2@DMSA nanoparticles. The morphology, structure, functional groups, surface charge, and magnetic susceptibility of the nanoparticles were characterized by transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectrometry, X-ray photoelectron spectroscopy, zeta potential analysis, dynamic laser scattering, and vibrating sample magnetometer. Cytotoxicity tests and hemolysis assay were also carried out. Experimental results show that the toxicity of sulfhydryl-modified Fe3O4@SiO2 core/shell nanoparticles in mouse fibroblast (L-929) cell lines is between grade 0 and grade 1, and the material lacks hemolytic activity, indicating good biocompatibility of this Fe3O4@SiO2@DMSA nanocomposite, which is suitable for further application in biochemical fields.

No abstract

No abstract

A surface modification method was carried out by reactive DC magnetron sputtering to fabricate TiO(2) electrodes coated with insulating MgO for dye-sensitized solar cells. The MgO-coated TiO(2) electrode had been characterized by x-ray photoelectron spectroscopy (XPS), energy-dispersive x-ray spectroscopy (EDX), scanning electron microscopy (SEM), UV-vis spectrophotometer, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The study results revealed that the TiO(2) modification increases dye adsorption, decreases trap states and suppresses interfacial recombination. The effects of sputtering MgO for different times on the performance of DSSCs were investigated. It indicated that sputtering MgO for 3 min on TiO(2) increases all cell parameters, resulting in increasing efficiency from 6.45% to 7.57%.

No abstract