Magnesium batteries offer an opportunity to use naturally abundant Mg and achieve large volumetric capacities reaching over four times that of conventional Li-based intercalation anodes. High volumetric capacity is enabled by the use of a Mg metal anode in which charge is stored via electrodeposition and stripping processes, however, electrolytes that support efficient Mg electrodeposition and stripping are few and are often prepared from highly reactive compounds. One interesting electrolyte solution that supports Mg deposition and stripping without the use of highly reactive reagents is the magnesium aluminum chloride complex (MACC) electrolyte. The MACC exhibits high Coulombic efficiencies and low deposition overpotentials following an electrolytic conditioning protocol that stabilizes species necessary for such behavior. Here, we discuss the effect of the MgCl and AlCl concentrations on the deposition overpotential, current density, and the conditioning process. Higher concentrations of MACC exhibit enhanced Mg electrodeposition current density and much faster conditioning. An increase in the salt concentrations causes a shift in the complex equilibria involving both cations. The conditioning process is strongly dependent on the concentration suggesting that the electrolyte is activated through a change in speciation of electrolyte complexes and is not simply due to the annihilation of electrolyte impurities. Additionally, the presence of the [Mg(μ-Cl)·6THF] in the electrolyte solution is again confirmed through careful analysis of experimental Raman spectra coupled with simulation and direct observation of the complex in sonic spray ionization mass spectrometry. Importantly, we suggest that the ∼210 cm mode commonly observed in the Raman spectra of many Mg electrolytes is indicative of the C symmetric [Mg(μ-Cl)·6THF]. The 210 cm mode is present in many electrolytes containing MgCl, so its assignment is of broad interest to the Mg electrolyte community.

Silicon is a promising alloying anode for lithium-ion batteries owing to its high capacity and low cost. However, its use has been hampered by mechanical failure arising from the large volume change upon cycling and by an insufficiently stable solid-electrolyte interphase (SEI). SEI formation depends on the Si surface, which is often an oxide (SiO x ). In this study we compare three different Si surfaces using Si wafers: 1.3 nm native SiO x , 1.4 nm thermally grown SiO 2 , and a SiO x -free surface. The oxide-free surface showed the worst electrochemical performance, never exceeding 94% Coulombic efficiency (CE). It also exhibited the thickest SEI and the highest overpotential for lithiation, which correlated with uninhibited electrolyte reduction and the incorporation of P-F species into the SEI. The oxide-coated surfaces performed significantly better, demonstrating a CE above 99% beyond the second cycle, low overpotential for lithiation, and a thinner and more stable SEI. The oxides lower the onset potential for electrolyte reduction, and yield an SEI with fewer P-F species. However, it was found that the CE with the native oxide surface decays from the fifth cycle onwards and correlates with a resurgence of electrolyte reduction. A 1-2 nm thermal SiO 2 coating is optimum for achieving a stable SEI that minimizes side reactions and sustains efficient cycling.

No abstract

The adsorbate-induced surface stress during the electrochemical oxidation of CO and NO on Pt is studied with in situ surface stress measurements and density functional theory (DFT) calculations. The changes in the surface stress response, Δstress, demonstrate the interplay between the adsorbed species during the oxidation process, which is determined by the coverage and the nature of the adsorbates. The oxidation of adsorbed CO, CO ads , shows a nonlinear surface stress response in both acidic and alkaline electrolytes, with the greatest tensile Δstress observed in the beginning of the oxidation where the CO coverage is the highest. Once a significant amount of CO is removed, OH starts to populate the surface and the Δstress becomes compressive. This surface stress development profilethe nonlinear stress development at high CO ads coverages and the inflection point due to coadsorption of CO and OHis further interrogated by DFT calculations. While a tensile to compressive switch in Δstress is observed during CO oxidation, the oxidation of another strongly bound diatomic adsorbate, NO ads , shows a continuous compressive Δstress. DFT calculations show that this behavior is attributed to the adsorption of the oxidation product, NO 3 − , which induces a similar magnitude of compressive Δstress compared to that of NO ads . Hence, the compressive Δstress from the oxide and hydroxide on the surface governs the surface stress response.

A trace amount of water in an electrolyte is one of the factors detrimental to the electrochemical performance of silicon (Si)-based lithium-ion batteries that adversely affect the formation and evolution of the solid electrolyte interphase (SEI) on Si-based anodes and change its properties. Thus far, a lack of fundamental and mechanistic understanding of SEI formation, evolution, and properties in the presence of water has inhibited efforts to stabilize the SEI for improved electrochemical performance. Thus, we investigated the SEI formed in a Gen2 electrolyte (1.2 M LiPF 6 in ethylene carbonate/ethyl methyl carbonate, 3:7 wt %, water content: <10 ppm) with and without additional water (50 ppm) at varying potentials (1.0, 0.5, 0.2, and 0.01 V vs Li/Li + ). The impact of additional water on the morphological, (electro)chemical, and structural properties of SEI was studied using microscopic (atomic force microscopy and scanning spreading resistance microscopy) and spectroscopic (X-ray photoelectron spectroscopy, attenuated total reflection Fouriertransform infrared spectroscopy, and time-of-flight secondary ion mass spectrometry) techniques. The SEI exhibits both potential-and water concentration-dependent trends in its morphology and chemical composition. The presence of additional water in the electrolyte causes parasitic reactions, which onset at ∼1.0 V, resulting in a reduction of electrolyte components and result in the formation of an insulating, fluorophosphate-rich SEI. In addition, hydrolysis of LiPF 6 creates hydrofluoric acid, which reacts with the surface oxide layer on the Si electrode, leading to a pitted and inhomogeneous SEI structure.