An orientational change from homeotropic to planar of liquid crystal (LC) mesogens and the microphase separation (MPS) domains is attained by the segregated skin layer at the free surface. This allows for an efficient in-plane photoalignment of the cylindrical domains. The surface segregation strategy is very simple and is therefore expected to open up new possibilities for the orientation control of various types of LC materials.

The surface effects and anchoring of liquid crystals (LCs) have long been significant concerns for material chemists and physicists.[1] The surface alignment of LCs by mechanical rubbing [2] is a widely recognized phenomenon and of particular significance in technological applications for display device fabrication.[3] Surface molecular orientations [4] and topographical grooves and undulations [5] of the substrate provide LC alignment effects. Furthermore, in the past two decades, the photoalignment of LCs on photoreactive polymer film surfaces by anisotropic irradiation [6] has become a significant method and an alternative to mechanical rubbing processes. The aligning substrates are not limited to polymer surfaces; various types of surfaces, such as hard inorganic materials [7] and soft bio-related interfaces, [8] can be used for the alignment induction. In addition to low-molecular-mass LCs, polymer LC materials are also aligned by the surface effect.[9] Despite the tremendous amount of accumulated knowledge and the number of potential applications, the surface alignment processes developed to date mostly involve manipulations on the surfaces of solid or condensed phases.Herein, we report on LC alignment alternation, which is attained by a modification of the free surface (air-film interface). The homeotropic surface anchoring effect and layer structuring at the free surface of calamitic LC molecules have been shown experimentally [10] and have been further verified by theoretical simulations.[11] To modify the free surface, the present approach adopts the surface segregation [12,13] of a small amount of a free-surface-active polymer. We demonstrate here that the coverage of the surface with the free-surface-active polymer leads to a homeotropic-to-parallel orientation change of LC mesogens, which further leads to an efficient in-plane photoalignment of microphase separation (MPS) domains of a relevant LC block copolymer by linearly polarized light (LPL).[14] With regard to the MPS alignment control, the important role of a top coat layer has recently been demonstrated by Bates et al. [15] In this case, a polar-to-nonpolar chemical conversion of the top layer is achieved to fulfill the requirement of spin-casting from an aqueous solvent and to provide a neutral (non-preferential) layer for the hydrophobic block copolymer during the annealing. In the present approach, in contrast, no additional coating procedure is required, providing a simple, versatile method for the desired alignment control of MPS domains.First, the alignment behavior of an LC azobenzene (Az) homopolymer (PAz in Figure 1 a; M n = 8.0 10 4 , M w /M n = 1.13, and g-43 8C-SmC-100 8C-SmA-120 8C-iso) was examined. A spincast film of PAz was prepared (thickness: 100-200 nm) from a chloroform solution. After annealing at 130 8C (above the isotropization temperature) for 10 min followed by gradual cooling via a smectic LC phase to room temperature, this film spontaneously formed the out-of-plane (perpendicular) orientation of Az side mesogens, a...

No abstract

We have developed a new high performance plastic substrate for flexible displays. The plastic substrate has a multi‐layered structure composed of a newly developed base film, hard coat layers and gas barrier layers. The plastic substrate has a unique balance of excellent optical properties, high heat resistance over 200 °C, and practical mechanical strength.

We have been developing a new transparent plastic substrate for flexible displays. The plastic substrate (OPS substrate) is composed of a newly developed base film (OPS film) and hard coat layers. The OPS substrate has excellent physical properties such as high transparency, low retardation and high heat resistance over 200°C. The coefficient of thermal expansion (CTE) is relatively low as 40–45ppm. The dimensional changes under various conditions including temperature and humidity were directly observed by using CCD camera. The electrical properties of the OPS substrate sputtered Indium Tin Oxide (ITO) at various temperatures were evaluated. The OPS substrate sputtered ITO at 200°C shows low sheet resistance as 10Ω/□ and it is almost same as that of glass substrate sputtered ITO under the same condition.