Lung cancer is a kind of malignant tumor with rapid progression and poor prognosis. Distant metastasis has been the main cause of mortality among lung cancer patients. Bone is one of the most common sites. Among all lung cancer patients with bone metastasis, most of them are osteolytic metastasis. Some serious clinical consequences like bone pain, pathological fractures, spinal instability, spinal cord compression and hypercalcemia occur as well. Since the severity of bone metastasis in lung cancer, it is undoubtedly necessary to know how lung cancer spread to bone, how can we diagnose it and how can we treat it. Here, we reviewed the process, possible mechanisms, diagnosis methods and current treatment of bone metastasis in lung cancer. We divided the process of bone metastasis in lung cancer into three steps: tumor invasion, tumor cell migration and invasion in bone tissue. It may be influenced by genetic factors, microenvironment and other adhesion-related factors. Imaging examination, laboratory examination, and pathological examination are used to diagnose lung cancer metastasis to bone. Surgery, radiotherapy, targeted therapy, bisphosphonate, radiation therapy and chemotherapy are the common clinical treatment methods currently. We also found some problems remained to be solved. For example, drugs for skeletal related events mainly target on osteoclasts at present, which increase the ratio of patients in osteoporosis and fractures in the long term. In all, this review provides the direction for future research on bone metastasis in lung cancer.

In response to the theme of environmental protection and green development in the world in the recent years, waterborne epoxy resin has received more and more attention. Waterborne epoxy resin has lower toxicity, but its low toughness limits the application range of waterborne epoxy resin. Here, we first proposed a method of toughening waterborne epoxy resin with aqueous polyamide salt solution. In this article, a series of waterborne polyamic acid salts is used as modification polymer to improve the high‐temperature resistance and other properties of waterborne epoxy resins by copolymerization modification. Waterborne polyamic acid salt is dispersed uniformly in the epoxy resin. After curing, by compared with the pure epoxy resin, a semi‐interpenetrating network is formed, the cross‐linking density and the high‐temperature resistance of the material are increased, and the glass transition temperature increases from 105°C to 116°C. The storage modulus at 300°C increases from 6.15 to 15.76 MPa. Thermogravimetric Analysis results reveal that the corresponding temperatures of 5% and 10% weight loss increase from 403°C and 419°C to 415°C and 435°C, respectively. At the same time, the toughness of the imide chain segment and polar groups lead to the improved adhesion of the epoxy system, the peeling strength increase from 0.51 to 1.24 N cm−1, and the lap shear strength at high temperature (100°C) increase from 0.58 to 16.97 MPa. The water absorption decreases from 1.51% to 0.66%. The developed waterborne epoxy resin is expected to be used as a high‐temperature waterborne epoxy coating in high‐temperature coatings and other applications.

Polyimide has excellent heat resistance, dielectric properties, and mechanical properties, and has a wide range of applications in aerospace, electronic packaging, and insulating materials. However, traditional polyimide is difficult to melt and dissolve, and its processing is difficult, which has become an important reason limiting its practical application. Therefore, the development of high temperature-resistant thermoplastic polyimide has become a research hotspot. To prepare high temperature-resistant thermoplastic polyimide materials, a series of thermoplastic polyimides was successfully prepared using 3,3 0 ,4,4 0 -benzophenone tetracarboxylic dianhydride, 3,3 0 -diaminodiphenylsulfone, 2,3 0 ,3,4 0 -benzophenone tetracarboxylic dianhydride, 9,9-bis(4-aminophenyl) fluorene, and 2,2-bis(3-amino-4-hydroxyphenyl)hexafluoropropane via a two-step method. The effects of non-coplanar structure and bulky groups on the solubility, processability, and thermal properties of polyimide were studied. The structure, heat resistance and thermoplasticity of polyimide were characterized via various methods. The results show that the glass transition temperature of the prepared thermoplastic polyimide is between 292 and 302 C, and has excellent thermal resistance. The processing viscosity of polyimides is as low as 9210 Pa.s, and it has a certain degree of processing properties. It may be designed to be used in high temperature-resistant hot melt adhesives for structural components, high temperature-resistant melt processing resins, or thermoplastic composite materials used in the field of aerospace in the future.

No abstract